wanhao d9 3d models
8746 3d models found related to wanhao d9.thingiverse
español Este es un remix para usar el fan de capa 4010 que viene original con la wanhao d9 utilizando el fan duct modelado por Kanaan. También incluí un soporte para el bltouch y una pieza para sostener el cuadrado con cables. ADVERTENCIA si se...
thingiverse
Sempre in italiano, che è meglio. ...Alloggiamento per la molla di recupero del cavo estrusore della Wanhao D9 MK2. ...In questo modo lavora molto meglio :-)
thingiverse
This is a replacement bracket for the Wanhao D9 -Y- motor mount. It provides more rigid motor support and gives a much better print quality. ...
thingiverse
X carriage mount to relocate the belt around the 2020 extrusion on the Wanhao D9. I used with different motor mount, idler mount and end stop mount. ...A longer piece of 2020 will be needed.
cults3d
an update of the Wanhao D9 mk3 to a Bowden extruder in E3D I made this update because I met problems extrusion with extruder direct drive of origin especially in nozzle of 0,8 mm
thingiverse
Wanhao D9 400 Alu bed dxf Parts 8 x 6mm spacers 6 x 6mm eccentrics 6 x M5 30mm cap screws I raised the 40mm x 20mm rails with 20mm spacers to avoid the Y motor. ...
thingiverse
After using my Wanhao D9 Mark2 printer for a while i think that a weekspot is the thin cables going in too the printer head near the plug. So i made this simple holder for it. ... Enjoy...
thingiverse
The biggest problem on wanhao d9 is the weight of the bed assembly, over 2700gr, the weight of this mod is 850gr per sheet, 1700gr both, the original carriege is 1529 gr and the glass, 1200gr. you can reduce further some weight by cutting the...
thingiverse
Spool holder suitable for Wanhao D9 For this spool holder, you'll need : * 2x Cone.stl * 1 print of each of the other files. And other parts : * 1x M8 threaded rod, ±250 mm long. ... * 2x M8 nuts (nyloc is better) * 2x 608 ball bearing * 1x...
thingiverse
I worked with Jack McSwain who had a Wanhao D9 to design an adapter to mount the Wham Bam Systems MUTANT to his system. Its a beta and I would welcome any comments on how it can be improved. This replaces the X carriage and the Mutant then...
thingiverse
The Wanhao D9 that I received has 5mm holes in the bed plate where the bed leveling screws pass through. The Bed screws are M3 so they have lots of wiggle room. I made this part and printed in TPU so that it installs in the hole on the bottom side...
thingiverse
simple fan duct for using all standard parts of the current d9 fan duct fittings and fan
thingiverse
Support pour cable de la tete Wanhao, sans cela il fini par se couper ( a peu pres 1200H d'impression, cable coupé) A imprimer en PETG, remplissage 50%
thingiverse
Feet for my custom D9. Took the stock casing and off so I needed to make my own. To fit the controller and the PSU underneath the printer. Also, the hole in the lid is for an 80x80mm fan to cool the board/drivers. I'm using the 32 bit MKS...
thingiverse
Did i mention it's the best looking cooler for the D9? ... The size and spec of the fan are: 5015 - DC 24 - 1W - Brushless - Ballbearing type (last longer - less noise) ...
thingiverse
Made to attach Tecnifibre squash balls onto the stock rubber feet on the Wanhao D9/Monoprice maker Pro Mk.1
thingiverse
Case to fit a TFT35 display on the Wanhao D9. ...Convenient to replace the original screen when installing a MKS GEN L motherboard
thingiverse
This is a custom print bed of Wanhao D9 (300 x 300 x 400) for Simplify3D. Attached you will find Instructions on how to install. ... Enjoy
thingiverse
this is an x bracket for the wanhao D9 to be fitted on hiwin MGN12H style linear rails. ... you will require 8 m3 cap heads with the length of 12mm and 4 m3 nylock nuts ( recommended)
thingiverse
Filament Guide For WANHAO D9 From Extruder Mount To Filament Spool. ... Got the idea from "https://www.thingiverse.com/thing:2835173" but didn't use any of their files just the basic idea.
thingiverse
This is the second version of the Linear Rod Mod for Wanhao D9 MK1. This version allows greater stability and smooth movement of the bed. You need 2x410\8mm linear rods and 2 long or 4 short linear bearings. ...The original holes fits perfect so it...
thingiverse
My version of adapter for Palette 2 (+Pro) for Wanhao D9 printer with Bondtech Extruder. Use hot glue to attach on the top. You can use original silicone ring for your comfort. ... if you need F360 file, toy can download it here:...
thingiverse
support for installing the AIO EVO hotend on the Wanhao D9, with TouchMi and 4020 fan AIO EVO: https://www.hotends.fr/fr/home/50-hotend-all-in-one-evo.html TouchMi: https://www.hotends.fr/fr/home/64-capteur-auto-leveling-touch-mi.html magnets:...
thingiverse
This allows the stock 2.2mm borosilicate glass that comes with the Wanhao D9 to be placed directly on the aluminum bed and actually be recognized by the sensor! I tried this setup with a slightly thicker piece of glass (about 3.5mm), IT WILL NOT ...
thingiverse
Pour synchroniser les moteurs sur Z sur la D9 500 il vous faudra : 2 tiges trapézoïdale de 600mm 2 poulies 20 dents 6mm 1 poulie lisse 1 courroie GT2 6mm longueur 1340mm + le tendeur modélisé (STL ci joint)
thingiverse
a larger bearing spool holder for the D9 mk2 as its impossible to do a hot swap. ... uses bearings of course, use this to secure it to the frame https://www.thingiverse.com/thing:3228335