wanhao duplicator 4s z axis brace and bushing 3d models

The RAMPS board is positioned very close to the edge of the enclosure, necessitating an offset design that relocates the power connectors and USB towards the back where the power supply and harness wires would be. Please use this adapter at your own...

I sought out a lower profile design that would be more substantial and utilize readily available threaded stem glides, which I found at Home Depot for $4 (Threaded Stem Glides SKU 141178). The design is uncomplicated. That's my preferred method of...

Worst case scenario, stretch the horizontal pole a bit longer) Two brackets hook under the rear of the frame, and the front-facing part provides bracing/support from the forward pull of the filament unspooling. Slot the two legs into the rectangular...

I'm using my Anet A8 and every time I adjust something, the z stop switch gets knocked out of place. It's really frustrating to keep fixing it, so I've decided to design a Thing that will solve this problem. This project is also an exercise in...

The 3D model is the precise replica of the original 3D design intended for the resin vat of the Duplicator 7.

I've found that the stage monkey design has been performing exceptionally well for me, effectively eliminating my Z banding issues. ...However, over time, it's started to flex, prompting me to create a more robust alternative.

Also, install with the UV film facing INTO the box to help protect it from external knocks. Once you have three sides fitted, loose fit the top sheet and install three top braces into the slots between posts, ensuring that the bottom of the braces...

On my Duplicator 6, the handle fits perfectly without any screws, providing a secure and stable fit. You may need to adjust the scale settings to achieve a precise fit on your specific printer model. I've made available multiple file options in the...

I was fed up with using bits of wire and junk to keep the door of my Duplicator 4x from closing. So, I designed a solution myself instead of searching for existing ones. The design is based on clips that attach to the top of the printer, swinging...

... is there for perfectionists like myself who want that last corner sealed tight as well. Also, be sure to check out my Wanhao D6/Monoprice Ultimate wire retainer if you haven't already - it's a lifesaver: https://www.thingiverse.com/thing:4051105

Here they are guys, the last feet you will ever need for your duplicator i3. :) NinjaFlex or similar flexible filament for these. ... Remember to support my work on: Instagram - Twitter- YouTube @webberen - THANKS!

A sturdy reinforcement to stabilize a drooping Z motor mounting bracket, ensuring it remains securely in place. Visuals are provided to demonstrate the issue this solution addresses. ... This part necessitates the utilization of extended motor mount...

Hardware 2 M4 x 10mm screws (bracket to bearing block) 2 M3 x 10mm screws (circuit board to bracket) Important Considerations Make sure to re-use the little plastic bushing on the screws holding the circuit board down to prevent damage to the board...

... its securing nuts. ... I utilized it to upgrade to a TR0801 lead screw with an 8mm diameter and a 1mm pitch, successfully shrinking my Z wobbles and errant layer issues. ...While these problems did not completely vanish, they became remarkably small.

I decided to create adjustable feet for the Duplicator i3 to get rid of the rocking motion mine gets while sitting on my desk, and also because I've read that other people wanted adjustable feet to level off their printers. It just slips onto the...

Mount a rear fan on your Wanhao D6 printer now with our direct compatibility kit, expertly designed to seamlessly integrate with this model, ensuring effortless operation. ...A successful installation should not pose any issues when adapting for use in...

Elevate your Wanhao printer's usability with a simple grip upgrade.\nIMPORTANT NOTE: Only NinjaFlex or similar flexible filaments will stretch over the button successfully.\nPrint Settings\nRafts: Not required\nSupports: Not necessary\nResolution:...

I added version 4 as requested, and used and scaled down this item from Thingiverse: http://www.thingiverse.com/thing:31986 for the foot. I also added a version 3 with a ninjaflex bubble to enhance vibration. I created an oring style cutout foot...

By Brian Khuu 2019 This is for a cheap filament sensor, that you can usually find on ebay. This time it will clip right on to the NEMA17 extruder motor of a Cocoon Create Touch and Wanhao i3 duplicator plus. Rev1:...

Initially, I didn't realize there was a difference in the width of the left and right sides of the Duplicator until I hung a left side holder on the right. There is a 7mm disparity so I removed 7mm from the length of the "hook" portion. UPDATE 2: I...

When swapping out stock Z rods for a 500mm rod, it becomes apparent that the new length is just slightly short of the original bracket's dimensions. This modification adjusts the rod downward without hindering its movement in any way. To eliminate...

Here they are guys, the last feet you will ever need for your duplicator i3. ...:)\r\n\r\nNinjaFlex or similar flexible filament is what these require.\r\n\r\n<blockquote>\r\n<h5>\r\nSupport my work on: Instagram - Twitter- YouTube \r\n@webberen -...

A reinforced bracket adds stability to the backplate and motor mount, making it an essential component for a reliable setup. The optional ball bearing provides extra support to the steppermotor's axis, ensuring smooth operation. To assemble this...

Z-layer shift is a nightmare waiting to happen with any print on the i3 Mini, but not anymore (ironically I had a few failed prints, printing these parts because the bed shifted again!). This part has an added ring at the bottom to fit inside the...

Remove two screws from the rod holder on the front panel and use one screw to secure the LCD in place. 8. Mount the enclosure onto the front panel. 9. Reconnect the flat cable. 10. Mount the bottom panel. ... These steps are not overly detailed, but you...

... or snap rings. You will need: 4 x M4 lock nuts 2 x M4x20mm bolts 2 x M4x10mm bolts Print Settings: Printer: Monoprice Maker Select Rafts: No Supports: No Resolution: .3 Infill: 30 Notes: Printed with two shells, which prove to be strong and robust.

I tried printing an air induction shroud for the Duplicator 6 but it was far too thin all over and square in the channel profile, which doesn't seem good for airflow. It was also relatively fragile during removal and Slic3r hated it. I think I'll try...

Also, take a look at my other project, which is a redesign of the x-axis: https://www.thingiverse.com/thing:3528084 This upgrade is designed for those who want more control over their belt-driven carriage. There are several ways to improve the...

If you're reading this, chances are good you have a Wanhao and are familiar with how its belt rubs against its bearing blocks. Before starting on an enormous print project that I've been working towards, I wanted to tackle this problem first, opting...

... be used: These parts were printed without support material. Utilizing PLA as the filament, I set my temperature to 195 degrees Celsius and moved at a rate of 50 millimeters per second, while also selecting layer height settings of 0.2 millimeters.