wanhao duplicator 4s z axis brace and bushing 3d models

A support arm was added to the back brace to prevent heated bed wires from getting tangled around the Y-Axis bed, particularly when it reaches its YLarge Limit. ...The Level Foot came from my local hardware store, similar to Mal3D's acquisition at Home...

Inspired by impressive results I achieved using this hack on my Folger Tech Kossel 2020: http://www.thingiverse.com/thing:1313461 This design is based on the same geometry as before, but with some cut-outs to snugly fit Azza's z-brace mod, check out...

Things to buy: 8x M3 x 10mm screws 4x M3 Nyloc nuts Z Braces may be found at: http://www.thingiverse.com/thing:921948 If you like these mods and want to fuel even more of them, send beer coupons to https://www.paypal.me/azza68. For a filament...

Print Settings: Printer: Wanhao Duplicator I3 V2 Rafts: None needed Supports: Not required Infill: 25% Notes: For optimal results, use PLA filament at 210°C and a bed temperature of 55°C. ... Post-Printing Requirements: Parts Needed: 6 M4 Bolts or Cap...

Things to buy: 8x M3 x 10mm screws 4x M3 Nyloc nuts Z Braces may be found at: http://www.thingiverse.com/thing:921948 If you like these mods, and you'd like to fuel even more of them, please send beer coupons to: https://www.paypal.me/azza68 If...

I've got the popular Z Brace mod installed along with a zip-tied Y pulley. When I put a new zip tie on the hex screw, it didn't like the added tension against the sleeve and pulley (resulting in rapid movements), so I removed it until I can get an...

Just another 12/18mm Z-Probe holder for the Wanhao Duplicator i3 plus. Intended to decouple the probe holder from the heat brake, because when printing above 220 degree Celsius, the plastic tends to loos stiffness. ...This is not acceptable for a probe,...

Here is a z tower brace mod that i created to meet my own needs and those of others who want to use all of their z height after installing a tornado extruder or any extruder taller than stock. B.O.M. 4x m3.5 hex nuts (to install in the new tower...

I also wanted to have an angle for Z and so it became a project. I have combined the two parts and I have to say that it works very well. The USB extension is from an online store and currently costs around € 5.50. There will be 4 pieces; M5 x15mm...

(Updated) i have updated the model with slightly bigger openings for the threaded rod. and also added a sat file for anyone that feels necessary to modify it as long as credit is given.. Here is a Z tower brace mod that I have created to fill a need...

This tiny accessory here is an X axis endstop specifically designed for the Wanhao Duplicator i3 Plus and its identical clones when utilizing a glass bed along with glass retainer clips. It provides an extra 8.5mm of clearance, which was more than...

Replacement part for Wanhao Duplicator 4S MK9 Extruder Top Plate, designed as a robust alternative. For those who over-tightened the central screw by mistake, this upgraded design has been tested and successfully used on my machine for three months...

A specialized holder mounts at the hot end cooling fan setup on the Wanhao Duplicator 4S, offering effortless removal and adjustment possibilities to reach critical components with ease. Printing at high temperatures demands turning around the fans...

I designed a customized Z end stop bracket based on the original model provided by Wanhao, but I grew tired of using theirs due to four loose floating screws that consistently caused problems. My version features secure fixed holes for the endstop...

I was experiencing a minor issue with my Y-axis motor being pulled in, which caused excessive belt wear and unwanted lines on my prints. To address the problem, you will need to drill four holes into the frame of your i3 3D printer, a task that...

... It basically met my requirements, but since I had swapped out my motor for a bigger one, it no longer fit properly. With this new mount, it's easy to use with any motor and you can still utilize the stock mounting system.

http://www.thingiverse.com/apps/customizer/run?thing_id=280974 Instructions Using the following settings: z_distance is set to 72 beam_height is set to 10 claw_depth is set to 25 wall_thickness is set to 3 claw_height is set to 15 beam_width is set...

The top cover enclosure for the Wanhao Duplicator 4S is not secured in any way and might even slide of the printer if you accidentally bump into it. To solve this problem we designed this simple bracket to fix the position of the top cover on top of...

I Created this Right hand side Gantry for Wanhao Duplicator 4s. ...I only created the Right side because the left side is already on the thingiverse but also that i was annoyed for haven to replace it as it broken for the second time in 1 year and this...

The hinges holding the door on the Wanhao Duplicator 4S moves very smooth, perhaps a little too much. As we like to open the door and not having to hold it up while turning our attention to what we are doing inside the printer we designed this...

The top cover enclosure for the Wanhao Duplicator 4S is not safely secured and may even slide off the printer if you accidentally bump into it. To solve this issue, we designed a simple bracket to keep the position of the top cover fixed on top of...

The Wanhao Duplicator 4S top enclosure slips free when touched and may even slide off the printer if you accidentally nudge it. We designed a straightforward bracket to secure the top cover in place atop your 3D printer. To fix this, print four of...

The hinges holding the Wanhao Duplicator 4S's door slide very smoothly, perhaps too easily in fact.\nWe wanted to create a print-in-place hinge that makes it simple to open the door without having to hold it up while focusing on the printer inside.

I also applied oil to the bearing and bushing. When screwing the bushing tubes into the metal plate, I used extra-long M3 screws so that the support would be securely pressed against the rest, making everything even more solid. This setup will...

Flexible Filament Adapter for Wanhao Duplicator 4 Series Requiring users to drill a precise 2mm hole in the filament passage is a necessary step. Instructions Successfully printed on my Wanhao Duplicator 4x with a PLA setting of .20 at 210°.

The hinges securing the door on the Wanhao Duplicator 4S glide effortlessly, possibly a tad too much. To avoid having to grasp the door while diverting our attention to what's happening inside the printer, we crafted this print-in-place hinge. ...It...

A more aesthetically pleasing Z-axis brace for the Artillery Sidewinder X1. ...Made from PLA and parts from an old Longer LK something printer.

I originally posted this as a Make on Connolly's design page but have been requested to supply the STL for the distance pieces and bearing tubes several times so figured this would be the best approach. I've not included the lowering blocks or the Z...

This is a Z-Brace kit I designed specifically for Maker Select/Wanhao Duplicator printers. My goal was to create a simple and straightforward Z-brace with as few parts as possible. To build this brace, you'll need the following printed components:...

These modifications are derived from AzzA's Z Extensions and Spacers for Wanhao Duplicator i3, Cocoon Create, and Maker Select. The original extensions can cause bending of the side tabs on the x crossbeam and rod retainers when installed. To address...