wanhao duplicator i3 manual 3d models
111725 3d models found related to wanhao duplicator i3 manual.thingiverse
These are the stl files for the improvements to the Wanhao Duplicator i3, V2 How I Designed This Design work all done in Blender 2.76.
thingiverse
Wanhao Duplicator i3 firmware. This firmware works with the original LCD and Melzi board. I had to create a custom thermistor table because the standard board uses 10k pull-up resistors instead of 4.7K. (Not sure how good the table is.) I also had...
thingiverse
Caisson imprimante Wanhao Duplicator i3 v2 partie arrière. Matériel nécessaire : - Plexiglass voir dimension dans les plans - Vis 3x8 tête large Il manque les deux perçages pour la bobine de fil en placement supérieur. Correctif...
thingiverse
Wanhao Duplicator i3 brace one uper left down right down. 0.2 mm print Iḿ trying to design a brace monted whit straps. Hope to get a build at minimum priced upgrade. Nuts and threaded rod needs as usual. ... but you dont need extra long ...
thingiverse
Filament guide for Wanhao Duplicator i3 Based on this model (http://www.thingiverse.com/thing:1358776) and modified to suit Wanhao Duplicator i3. ...Print Settings Printer: Wanhao Duplicator i3 Rafts: No Supports: Yes Resolution: 0,02 Infill: 20%
thingiverse
Wanhao Duplicator i3 mini-bed Tension You will need m3 bolt and nuts
thingiverse
Wanhao Duplicator i3 led light. Plug into extruder fan. ...Hot end fan: http://www.thingiverse.com/thing:1246425
thingiverse
Tool for Z-alignment of the Wanhao Duplicator i3. You need two of these. Move the printhead up a little. Then snap the aligners onto the lower bar, one on each side. ... With the steppers turned off, manually turn the left and rigth steppers until...
thingiverse
... clip or the one I designed. ...The lock is optional, but works well. This thing was made with Tinkercad. Edit it here. Print Settings Printer: Wanhao i3 Duplicator Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 50% or more
thingiverse
This is a cover for the LCD of the Wanhao Duplicator i3. ...It has space to add a stop button into the unit as well.
thingiverse
This is a stand-alone servo mount for the Wanhao Duplicator i3, in the use of Auto bed leveling/compensation. ... It replaces the stock part cooling fans location.
thingiverse
M3 12mm , Nut x 2 4- 5mm LED x 4 The cooler I am using is WANHAO i3 Fan duct.http://www.thingiverse.com/thing:1246425 I made it with reference.http://www.thingiverse.com/thing:1477031 Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3...
thingiverse
Improved parts for Wanhao duplicator i3 mini. ... Fan protection based on this: https://www.thingiverse.com/thing:2830254 Fan duct is a slightly improved version of this model: https://www.thingiverse.com/thing:2828554.
thingiverse
A simple cable guide for the heatbed wires on a Wanhao Duplicator i3. Snaps on to the back of the printer and uses a zip tie to hold the cables down. ...Easy & fast print.
thingiverse
This is a filament guide/holder. ...Print Settings Printer: wanhao duplicator i3 Rafts: No Supports: No Resolution: 1:1 Infill: 20% Notes: Printed in PLA at 135c and med 50c
thingiverse
This is a guide for filament from from spool yo the extruder. ...It helps to prevent tangle. Print Settings Printer: Wanhao Duplicator i3 Rafts: No Supports: No Resolution: 0.2 Infill: 10%
thingiverse
Just another Spoolholder for the Wanhao Duplicator i3 Plus that allows use of wider/ bigger filament spools. ...In addition to the 3D printed part, it requieres some solid pipe of 20mm diameter and sufficient length (I used aluminium).
thingiverse
Filament spool riser for Wanhao Duplicator i3. Works with Saaber's filament guide. Allows larger filament spools to fit on top. ... Requires two M5 x 30 mm cap screw bolts.
thingiverse
... guide can be added. Print Settings Printer: Wanhao Duplicator i3 Rafts: No Supports: Doesn't Matter Resolution: .1 Infill: 100 Notes: When printing I used hatchbox black PLA at 213 degrees.... ...The unit was sized to fit so no scaling was required.
thingiverse
... tool holder by berky93. ... I added an extra hole for the cleaning tool and also added a hole to hold my calipers. Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 Plus Rafts: Doesn't Matter Supports: No Resolution: 0.1 Infill: 25%
thingiverse
... using the filament spool holder mounted to the top of the i3. The original design file is provided (from 123D Design); feel free to remix, etc. Print Settings Printer: Wanhao i3 Duplicator v2 Rafts: No Supports: No Resolution: 0.2mm Infill: 25%
thingiverse
# Wanhao I3 Duplicator BLTouch Bracket # Summary When I was upgrading my Wanhao Duplicator I3, I looked into adding bed levelling to the printer. To do this, I used the BLTouch unit and upgraded the Wanhaos firmware to incorporate this sensor. Doing...
thingiverse
... with 6 mm lift and without any additional screws. ...Print Settings Printer: Wanhao Duplicator i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.1 Infill: 100% Notes: Use lines as support pattern. Holes may need some drilling. ...Printed in PLA.
prusaprinters
A simple cable guide for the heatbed wires on a Wanhao Duplicator i3. Snaps on to the back of the printer and uses a zip tie to hold the cables down. ...Easy & fast print.</p> Category: 3D Printer Accessories