wanhao i3 z brace 3d models
134249 3d models found related to wanhao i3 z brace.thingiverse
Changed these to fit a 1/4th inch nut that comes with the ultimate3dprintingstore kit.
thingiverse
I added a loop to guide the cable going to the right Z-tower on my Wanhao Duplicator i3 v2.1 Type 1 is just a loop that goes straight down to the bottom. ... Type 2 is a remake with a near-full loop to hold the cable in place as I use the dampeners...
thingiverse
I also used Azza's "Z braces for Wanhao Duplicator i3:http://www.thingiverse.com/thing:921948 In addition to my versions, just print the top_right, top_left and 4 of the MK2 balls from Azza's braces. Use these with Anti-vibration feet for Wanhao...
thingiverse
When I printed this originally, I didn't understand why there was a cylinder in the center. It's a pain to remove and prevents threading the rods through the print. ...So I fixed it for a quick 1 am re-print, and it worked.
thingiverse
BOM- Printed parts -Z brace Bottom Left -Z brace Bottom Right -Z brace Top Left -Z brace Top Right -(2) Support foot small -(2) Support foot large -(6) Support foot pad, 6 is optional, 4 are required minimum. ...Hardware -(20) 3/8"-16UNC grade 5 nuts...
thingiverse
... ... This is a snug snap-on bracket for the top of the printer, where you want to feed the filament through the side from a spool holder or dry box. The arm where the filament passes is extended so it does not interfere with Z-axis brace.
thingiverse
I added a support arm on the back brace to keep the heated bed wires from getting tangled on the Y-Axis bed, specially when the Y-Axis is at its YLarge Limit. I got the Level Foot from my local hardware store. I think Mal3D got his at Home Depot. ...On...
thingiverse
Yet another Z-brace mod for the Wanhao I3 Plus (should work with Plus Mk2 as well). Easy to mount and doesn't require much material. A sample roll of filament should be enough. Apart from the printed bits all you need is two 8mm threaded rods...
thingiverse
These are the printable parts for a rear z-brace for the Wanhao i3. I made it for my Monoprice Maker Select V2. I wanted them in the back so that I still had clear access to everything from the front of my machine. It's designed to fit 5/16...
cults3d
If you have a Z-Brace installed and use thumb screws the original will not work. ...This one will.
thingiverse
If you have a Z-Brace installed and use thumb screws the original will not work. ...This one will.
thingiverse
It's a simple design of Z braces that mount the the rear of the Wanhao Duplicator I3. I designed this to replace the famous Azza's Z braces that was installed on my printer. I wanted a design that mount to the rear instead, but without being...
thingiverse
I have included the updated brackets with the locking lugs if you want to use this enclosure/z-brace combo. Just be aware that the rear enclosure has to sit 5mm higher either through supports, or through modification of the laser cut templates. See...
thingiverse
I was looking for a Z-brace kit for my Maker Select v2 and found one here by f0xox that looked simple enough and wasn't overly complicated: https://www.thingiverse.com/thing:3603327. I loved the design by f0x0x but when I printed it and mounted up...
thingiverse
This is the Cocoon Create Touch / Wanhao Duplicator i3 plus Z Axis Brace mod I created from using this video as a guide. I have uploaded the individual STL files from those creations. https://www.youtube.com/watch?v=Xxr2GkDVfV8 As mentioned in the...
thingiverse
This is for the nuts that come with the Z-Braces for the Wanhao Duplicator i3 purchased from the Ultimate 3D Printing Store. http://ultimate3dprintingstore.com/ I am in no way affiliated with them. I just like buying stuff from them. You will want 2...
thingiverse
Z-braces for Wanhao duplicator i3 v2. These braces may not be as rigid as some other designs but it has some advantages. It´s still like day and night compared to a non braced frame and I can print at twice the speed with even better results than...
thingiverse
I've seen alot of the metal rod z-braces, and wanted to design something to give my wanhao duplicator i3 a little bit different look from the rest, so I designed what I will be calling "The Roll Cage". When it is fully assembled and attached to the...
thingiverse
... - I tried without one but it didn't stick well enough. Should print without supports but if you enable supports you might get a slightly better finish on top. I have a cable cover on my 5/16" Z-brace and don't even need a screw, it's a tight fit.
thingiverse
This is all printable Z braces for Wanhao i3 (just some m3 screws is needed) i didnt have the hardware to create the real Z braces for Wanhao i3http://www.thingiverse.com/thing:921948 so i design this one fully printable its a quick and dirty jobb...
thingiverse
A remix of Azza's "Z braces for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers."http://www.thingiverse.com/thing:921948 Just print the top_right, top_left and 6 of the balls from Azza's braces along with the 4 STL's...
thingiverse
If you installed your Z-Brace mod on your Wanhao,MP Maker Select, or other similar 3D Printer, you likely noticed your gantry feet no longer touch the surface of where it sits. These fill that gap to provide further stability. ...Print Settings Printer:...
thingiverse
After performing the Z-brace upgrade for my Maker Select V2 I wanted to cover up the unsightly threaded rods without using that ugly and costly store-bought cable loom. The design is 100mm high and seems to be the highest I can print it uniformly on...
thingiverse
... Di3 giving you better prints more often. ...I did not like the designs I found therefore I made me one design. Use M8 nuts and M8 thread rods This are the parts for the right side of the Duplicator I3. ...Please mirror this parts for the left side.
thingiverse
This is the wire box from here: http://www.thingiverse.com/thing:1261720 That I merged together with the back feet from the z braces thing from here: http://www.thingiverse.com/thing:921948 The whole piece doesn't fit on the printer plate so I also...
thingiverse
... glue on the end stop bearings may be good. May you need the source, check this repository out https://github.com/loian/Wanhao_i3_zbrace you can open the source file with Autodesk 123d (an old software but still available somewhere on the internet)
myminifactory
Following the lead of FilamentCorner's z Brace and z Extensions (Z-Kit) http://www.thingiverse.com/thing:2012743, I decided to make a hybrid design that moved the braces to the back of the printer so as to be out of the way. All of this is based on...
thingiverse
I originally just had front z-braces but I wanted to switch to rear braces so it would be easier to get prints off. I found this design and I really liked how simple it was: https://www.thingiverse.com/thing:2438817 I really liked being able to...
thingiverse
This is a remix of 3dspool_canada's feet for the i3 PLUS to be used with Azza's popular zBraces. ...This version is only a slight modification in that it allows to use two nuts on each foot in order to stabilize the gantry in both directions...
thingiverse
Kossel 2020: http://www.thingiverse.com/thing:1313461 It's basically the same geometry with some cut-outs to snuggly fit Azza's z-brace mod, see photos. /Update June 2016: Some people had issues with the dampeners "collapsing" within a couple of...