warp 9 motor 3d models

Model based off of schematic available from NetGain Inc. ...(2017)

2017 Capstone Project. ...Built for a 1963 Volkswagen type 1 Beetle.

These files are several that I made for my DIY '68 el Camino electric conversion to allow me to seal up a set of NetGain Warp 9 motors and force air into them using 4" diameter bilge pump blowers.

Netgain Motor for EV conversions. ...Dimensions from Netgain Drawings.

The tunnel effect in Space Mountain at Disney is always fun, so I made an extrusion motor visualizer based on that idea.Like my other models, this one is heavily detailed, so a 0.25mm nozzle is strongly recommended - I used a 0.1mm layer height...

Solidworks model of the T-Motor 4120-9 400kv commonly used on multirotors.

9 cylinder aviation engineMotor de aviación de 9 cilindros

Please use the same safety procedures that apply to other motor applications as well as the common sense that comes with revolving magnets inside of a plastic rotor that's been inserted into a plastic stator which has electricity applied to the wire...

Basic soft mount for 9x9 motor hole pattern, usually for 1103 to 1303 size motors

This is a 9 cylinder dummy motor and motor mount that goes around a 200kv electric brushless RC airplane motor. This model is part of our new Fokker DR1 3D printable airplane we are releasing this month. ... Take a look at the complete instruction blog...

Motor Hidraulico-Vista-9 MPa Kw 1,8/2,6 rpm 1950/2450 Pressão 100/200 bar Vazão Lt/min 12/20 Deslocamento cm³ 8,2 Torque N*m 11/21

This is a Gearbox Housing for a 9-18V Motor I got at Radio Shack (http://www.radioshack.com/radioshack-super-speed-9-18vdc-hobby-motor/2730256.html). The Internal Gears and Hardware are from a Tamiya Gearbox (https://www.pololu.com/product/114). I...

<p>I don't know what came over me but I just felt the trolling hadn't quite reached maximum saturation.</p> <p>7 different models hidden in there. This is not printable (without more support than model) and no I'm not slicing it up. It was hard...

I don't know what came over me but I just felt the trolling hadn't quite reached maximum saturation. 7 different models hidden in there. This is not printable (without more support than model) and no I'm not slicing it up. It was hard enough putting...

XYZ daily 11.02.2020

Warp Engine

warp_pipe1

My version Of the warp core.

Inspired by Warp Pylon Legacy of the Void Starcraft

Das ist ein Modell der warp blase von alcubierre. ...Ich hoffe es gefällt dir

I took the common "heart on top of heart cake" and warped it a little!

This is a Warp Stabilizer intended as terrain in the Warhammer 40k universe.

Single piece warp core. ...Relatively accurate to The Next Generation series.

Корпус топливного фильтра для лодочного мотора SeaPro 9.9 (Yamaha 9.9) Filter corpse for seaPro 9.9 (Yamaha 9.9) boat motor

One of the projects I was looking to make some head way on during my artist in residency at Maker Media Labs is/was “Weft / Warp.” Last summer I produced a body of work called “Plotting Curves” the majority of which will be exhibited next week at The...

A small, simple device for protecting the corners of a print from drafts that can lead to warping or corners raising off of the print bed. Not all warping is due to drafts, but if your printer is in a high traffic area or by a window this can...

Hyper 9 Motor with SME Inverter

DC 9-60V motor controller 20A

Evo 9 ACD Pump Motor Body Assembly

I Remix this Warp Gate cause I really hate supports. ...This version can be print without supports but need assembly.Original file from Eli (http://www.thingiverse.com/eliahu77/about)