washer fluid cap 3d models
118375 3d models found related to washer fluid cap.thingiverse
this is washer fluid cap printed for my ford focus c-max, but it can be fitted to any washer fluid tank with throat diameter 44mm.
thingiverse
Washer fluid reservoir cap for Komatsu wheel loader. ...Propably fits other vehicles also.
thingiverse
This is a replacement windshield washer fluid cap for a 2010 Land Rover LR2. While filling up the windshield washer fluid one day, the cap popped off and was lost. ... No problem, I just made a new one and popped it on.
thingiverse
Although it will probable fit many other vehicles of the era, this is a replacement **Washer Fluid Bottle Cap** for my ***1994 GMC Sierra Pickup*** truck. ...It should be printed using a Flexible Filament.
thingiverse
This is a 60mm ID washer fluid cap made for Nissan s13 S-Chassis. I really don't know if it will work on other cars, but I did state Diameter for this print, so measure before you print. I used PLA for th first print and it did warp after the...
prusaprinters
This is a replacement windshield washer fluid cap for a 2010 Land Rover LR2 (I haven't tested others but I expect it may fit other models).While filling up the windshield washer fluid one day, the cap popped off and was lost. No problem, I just made...
thingiverse
E46 windshield washer fluid cap for the rear reservoir in touring and compact models.
cults3d
Washer fluid cap for Peugeot 407 (sedan or sw). ...Fits nicely on my car and stays tightly on.
thingiverse
Designed for use in 2015-2023 Ford Mustang's to replace the OEM Washer Fluid Cap for a cleaner look.
thingiverse
As the OEM windshield wiper fluid cap started falling apart, I needed something new to protect that fluid reservoir. Instead of buying a new one, I decided to have some fun with it! I printed the cap with the bee facing upwards and supports...
thingiverse
Washer Fluid Cap for Honda Jazz 2002 Material: PETG Infill: No Layer height: 0.2 Central pin have to be melted after fluid level measuring road is assembled.
thingiverse
This is a washer fluid reservoir cap for a 2016 Ford Kuga'
thingiverse
I was missing a washer fluid cap for my car, so I designed one. ...I am sure it fits more models, but is designed for the Mazda 6 gen 2.
thingiverse
This is a washer fluid tank cap for Honda Civic IX, but maybe it will be OK for the other models. The Tight version version snaps pretty tight. The Normal version is with 0.2mm wider diameter. I have not testet it, but I think that it will be...
thingiverse
I am designed another S13 washer fluid cap because what I found there on Thingiverse, isn't fit. So if you have S13 and the measured diameter what is shown on the picture is 57-57,4mm, this cap fits for you. I am printed it with ABS and heated the...
prusaprinters
Washer/Wiper fluid cap for 2015 Cadillac ATS. I printed mine at 0.3mm layer height. Supports used for inside rim of cap, but blocked supports for the bottom emblem. You will need to use a heat resistant filament (NOT PLA). I...
thingiverse
This is a windshield washer cap for a 2011 Ford Figo. It also fits a Ford Fiesta. ... Should print with the main ring on the bed of the printer.
thingiverse
This is a cap for the windshield washer fluid reservoir on a 2016 Ford Escape.
thingiverse
This is a cap for the windshield washer fluid reservoir for a Porsche 944, probably fits more cars, like porsche 928. ...
thingiverse
Window washing fluid cap for CBC mobile trucks and other sprinters.
prusaprinters
This is a threaded cap for the wiper washer fluid tank of a citroen C4, it consists of two pieces. The first piece fits by preasure and the second one screws to the first one acting as a cap.I'm not sure if it can fit other citroen models or even...
thingiverse
I designed a washer cap for the Peugeot 307 for a work collegue. I designed it to be easy to mount. The base can easily clamp the bottle neck. I would recommend to print it in ABS or PETG. ... Hardware required: 1 x M3 nut 1 X M3 25mm long bolt.
thingiverse
This is a resized cap for a 2000 Kia Sportage. I printed it in Bambu Labs PETCF but you can probably just use PetG. ...
thingiverse
Made from TPU to replace the broken cap on my 2016 Ford Focus. should fit other models. ...filler neck is 2.1" at the bed and 2" at the bottom.
thingiverse
Remixed the cap by Gmorris with an ST logo. Printed in PETG because I had better colors on hand. Believe it should last within this part of the car's engine bay. ... Some risk of shrinking after heat, but I think the design should be sufficient to...
cults3d
This is windshield washer fluid reservoir cap for Mercedes ML (2003) Whole collar was damaged so there are two parts that fits together - a funnel and a cap
thingiverse
This is windshield washer fluid reservoir cap for Mercedes ML (2003) Whole collar was damaged so there are two parts that fits together - a funnel and a cap
thingiverse
Ford c-max 2011 windshield washer fluid cap. Printed in tpu. Stock cap keeps breaking so I decided to make my own. ...My bottle neck diameter is ~51mm.
thingiverse
Peugeot 508 2010-2018 windshiled washer fluid cap, also fit to other PESA group cars. Fasteners (DIN or similar): Bolt M5x20 or M5x25 DIN912 - 1pc. Washer A5.3 DIN125 - 2-4pc. ... Nut M5 DIN934 - 1p.c