watercooling reservoir 3d models
2722 3d models found related to watercooling reservoir.thingiverse
Needed to upgrade watercooling setup for couple of my PCs and thought that why not design my own reservoir? So this is the first design and I printed couple of these using PETG and Filaflex for gaskets. Designed for immersive pump, Im using Eheim...
prusaprinters
Needed to upgrade watercooling setup for couple of my PCs and thought that why not design my own reservoir? So this is the first design and I printed couple of these using PETG and Filaflex for gaskets.</p> <p>Designed for immersive pump, Im using...
thingiverse
Mount a 50mm diameter watercooling reservoir to a 12cm fan mounting holes.
thingiverse
... dispo sont compatibles avec les tuyaux de diamétre 10mm interne. This is my DIY watercooling reservoir made using only 3D printed parts, of course it can be used for other purposes. ...The fittings availables are for 10mm inner diameter tubes.
grabcad
My first design, a watercooling custom reservoir representing the World of Tanks Logo, will be used in a thematic PC build.
thingiverse
This is a PC Watercooling reservoir holder with a diameter of 50mm. It is designed to be used with a countersunk M4x16mm screw. It is meant to be mounted in a M4 thread, in my case on the side of the 5,25 Inch Bay of my Lian Li PC A70 Case. Of...
thingiverse
This is the support for the reservoir of my DIY watercooling project, it's made to be install on the 5,25" bays in the front of a computer case.
thingiverse
This is a NEW version of my PC Watercooling reservoir holder with a diameter of 50mm. https://www.thingiverse.com/thing:3900098 Easy to use, snap on mechanism! I printed it in PETG, but PLA should do the same. ...
thingiverse
This is a Watercooling reservoir holder for 60mm diameter reservoirs (more specifically the EKWB 250mm X3), but the model is compatible with all other 60mm diameters reservoirs with minor adjustments. It notably has a LED Strip channel which allows...
grabcad
This assembly has 6 configurations for each of the available sizes (ranging from 110mm up to 400mm). ...I made this model for my own convenience, but though it might be usefull for you guys as well.Currently only available as SolidWorks files, but when...
thingiverse
Print best in TPU, -Slide the RGB Connector-Cable through the hole -Cut LED-Strip to correct length -Solder -Put Ring over the Reservoir -Wire it -Light it up -Enjoy :)
thingiverse
... used to drop a Heatkiller reservoir down. ... You may need these if you mount your heatkiller reservoir to a radiator, but the included mounting brackets don't let you mount the reservoir as low as you need to. ... Printed in PETG with a 0.8mm nozzle
thingiverse
Used to hold the custom watercooler reservoir tank 50mm, (clamp) printed on ender 3, used generic petg pattern that already comes in ultimaker cura 5, nozzle 0.4mm no need support to print.
thingiverse
Open air case for RPI3 (might work with older/newer models to). ...It has a reservoir with cap for holding water. I coated mine with clear spraypaint; but might not be required if you have good layer adhesion. ...The nozzles are for standard 3mm tubes.
thingiverse
This is a mount to fix a heatkiller pump/reservoir combo on a Watercool MoRa 3. You need to print one of each parts. The two bracket halves are held together by 2 M3x30 bolts. There is no hex nut needed, the thread should hold well in the printed...
thingiverse
I got bored of my watercool reservoir , The LF reaction T Virus is cool but got old. Added segmented parts if you want to modify your own to suit less or more ring's. Increase the fin's etc. ...
thingiverse
SUPPORT POUR NF WATERCOOLING HOTEND JE PEUX MODIFIER AU BESOIN SUPPORT POUR FAN30X30X10 N'HESITEZ PAS A DEMANDER
youmagine
This designs are about my Hackintosh which I built. ...These parts are for the aquacomputer filter and the EK-XRES 140 Revo D5 PWM reservoir and pump unit for my watercooling system. ... the full project is on my page: http://s-technologies.eu
thingiverse
My friend wanted to install a watercooling in a Silverstone FT03 Mini (http://www.silverstonetek.com/product.php?pid=333) but he has not handler to fix the pump...
grabcad
Various Standard Watercooling Fittings. Modeled off Bitspower Components. Right Angle Male-female Male to Male adapter Male to Male Short adapter Female to Female Adapter 3/8" (10mm) ID Compression Fitting. ...Standard G1/4" Through Port
thingiverse
This insert replicates the EK ABS inserts that prevent PETG tubing from buckling under load and becoming loose in watercooling fittings. PETG can warp around 50 to 60 C which watercooling temps will exceed, especially after leaving GPU. This can...
thingiverse
Autant je peux faire des choses jusqu'à réussir comme pour ce watercooling autant je peux vite lâcher l'affaire quand il s'agit de chercher une info sur le net... Le fichier test sert à vérifier si vos impressions et le collage au sillicone sont...