watering spikes 3d models
68734 3d models found related to watering spikes.thingiverse
# Watering Spikes These watering spikes are used for watering plants. They guide the water directly into the soil to the root of the plants. The connectors on the left and right side are optimized for 1/2'' tubes and can be customized in the...
thingiverse
Modified Jason's watering spike to be more similar to some I have used in the past, with holes going down the side of a thicker spike. Original: https://www.thingiverse.com/thing:4796816 This should be printed with extra walls and at least 20%...
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
This is the *Water Spike*, a manual watering tool used to give each plant the same dose of water, slowly dripping (*Version 2.1*) or flowing (*Version 4*) onto the ground next to the plant. This limits the horizontal spread of the water, applies as...
thingiverse
Yet ANOTHER watering spike i threw together, mixed with https://www.thingiverse.com/thing:1667333/files
thingiverse
Watering spike can be attached to most water bottles, or even the 1-liter and 2-liter pop bottles.
thingiverse
This is a derivate of another watering spike. It will hold two 1,5l bottles (maybe even 2l) for watering your plants. You can also use it in a deeper pot. ... Instructions I don't have a 3D-Printer yet...
prusaprinters
The watering spike helps deliver fresh water to your plants roots. Designed with large and outdoor plants in mind, It helps water penetrate even the most hydrophobic soils. It features radial holes as well as a bottom hole, and a large inlet for...
thingiverse
Just a quick and dirty merge bw the toad and a water spike found here: https://www.thingiverse.com/thing:1667333/files Has NOT yet been printed, but I'd hazard a guess that it should be oriented upright for best results, with a couple column supports...
prusaprinters
Then be sure to check out:Website: https://www.3Dplanner.beInstagram: https://www.instagram.com/3dplanner.beFacebook: https://www.facebook.com/3Dplanner/TikTok: https://www.tiktok.com/@3dplannerTumblr:...
prusaprinters
Just a quick and dirty merge bw the toad and a water spike found here: https://www.thingiverse.com/thing:1667333/files Has NOT yet been printed, but I'd hazard a guess that it should be oriented upright for best results, with a couple column supports...
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
cults3d
So I made this watering spike. My bit of testing showed that it took about 12 hours on average for the water in the 2L bottle to drain. It lasts a little longer if the ground is wet to begin with. EDIT 7/26/11: Spike with Threads added. This one...
thingiverse
Instructions Print (I used a raft and 100% fill), fill bottle with water, screw spike onto bottle, plunge into ground. I never got around to putting threads on this, so it's a little weird getting the spike on the bottle. You may want to print out...
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
thingiverse
Customized version of https://www.thingiverse.com/thing:2937504 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2937504
cults3d
Easy to use, just fill standard soda bottle with water and thread water spike on and insert is in flower pot. You may need to experiment with hole size for get best results, all plants need different moisture and water will be absorbed differently...
thingiverse
Improved Water Spike that for me works best, with a slightly modified thread and a washer added.
thingiverse
A version of Jasons PET-bottle watering spike, using less material and cutting the print time from 2,5 hrs to 1 hour (on my printer)
thingiverse
Bottle holder for progressive watering with a bottle. 2 versions: one with valve and the other without. Support de bouteille pour un arrosage progressif. ... 2 versions : une avec valve et l'autre sans.
thingiverse
I found that any holes would drain the bottle too fast, so I made this to just let the porosity of the print leak the water out slowly. Update: found that the base was too thin and most cracked after repeated use. ...Revised to have a thicker base.
thingiverse
I had tried several other plant watering spikes but they all broke if you tightened them too much so I designed my own. I got stuck when I found out that standard bottles don't use either a standard or metric thread type, instead they have their...