wd40 inventor 3d models
15739 3d models found related to wd40 inventor.thingiverse
Replacement cap for 400ml WD40 container. "clic" and it's in place ! If this becomes too hard to remove, then slightly scale it up finely (like +0.5% or +1%). **NOTE** This mesh is optimized for 0.2 mm layer height and 0.4 mm nozzle...
prusaprinters
Replacement cap for 400ml WD40 container."clic" and it's in place ! ...If this becomes too hard to remove, then slightly scale it up finely (like +0.5% or +1%).</p><p><u>Optimal print settings :</u><br><br>Layer height : 0.2 mm<br>Wall lines...
thingiverse
This printed quite well on my Flashforge Finder but it did need a little sanding to fit my WD40 can. I think this is due to the entry/exit points during the print, as the straw is so small it appears slightly misshapen. I had it in my can after about...
thingiverse
I designed a WD40 can holder (diameter 54 mm) that can be mounted on a wall. It consists of two parts - bottom and top. ...Each part has a 3mm hole for countersunk screws.
thingiverse
I needed someway to mount my webcam so I could use octoprints timelapse feature. ... I had a can of WD40 handy and figured this would be a good stand and lo the WD camera mount was born. ...
thingiverse
I keep losing those little straws that come with WD40 and other aerosol lubricants because they come taped to the can but then it either slips out of the tape later or it gets eaten by a gremlin, etc... So I figured this was a job for my makerbot. ...
prusaprinters
I designed a WD40 can holder (diameter 54 mm) that can be mounted on a wall. It consists of two parts - bottom and top. ...Each part has a 3mm hole for countersunk screws.</p><h3>Print Settings</h3><p><strong>Printer Brand:...
thingiverse
Wall mount for a small can of WD40 or similar product with a diameter of 50mm. Added a little slot on the side to hold straws as I keep losing them! Snug fit so scaling up by 1-2% wouldn't hurt but I only needed 1 so didn't bother. Object height...
thingiverse
Can holder for sprays like WD40/Caramba 70 with a diameter of 54mm File can be modified easily on Tinkercad https://www.tinkercad.com/things/2HKaNcxkSUg-caramba-70-wd40-derivate-holder
thingiverse
Formschöner Halter, der eine große Dose WD40 wunderbar umschmeichelt. ... Braucht man nicht, sieht aber schön aus an der Frenchcleat-Wand ;-)
thingiverse
Понадобилась подставка для баллона с WD40. Крепится на два мебельных шурупа 3*25. Всем Добра. ...Print Settings Printer Brand: RepRap Printer:...
thingiverse
WD Holder for ToolBoard First part of the Toolboard project here : https://www.thingiverse.com/thing:4458062 Toolboard project part II : https://www.thingiverse.com/thing:4507728 Youtube link : https://www.youtube.com/watch?v=HtnSrxiBCY4
cults3d
This is a simple 75mm spray nozzle extension für WD40 or other aerosols ;) 190129: different shaft-diameters added (2,8mm / 3,0mm / 3,2mm / 3,4mm / 3,6mm) to fit more aerosol-cans (for WD40 3,0mm-version should fit) Fusion 360 .f3d-data added for...
thingiverse
The adapter allows the use of straw from WD40 with a normal syringe. ... The handles are from @me5647, 10mL B-D Syringe Handle (https://www.thingiverse.com/thing:1242346) The Fusion 360 file is also here.
prusaprinters
The adapter allows the use of straw from WD40 with a normal syringe.The handles are from @me5647, 10mL B-D Syringe Handle (https://www.thingiverse.com/thing:1242346)The Fusion 360 file is also here.
thingiverse
... and exported separate STL's for both cans. The PC duster version is 57.75mm and the WD40 version is 65.85mm. If you need to modify the diameter of the ring of straw you can edit the SCAD file by simply changing the variables at the top. ...
grabcad
THIS IS THE BEST BEGINNER EXCERCISE IN AUTODESK INVENTOR PLS SUBSCRIBE AND WATCH MY CHANNEL