webcam side mount 3d models
525472 3d models found related to webcam side mount.thingiverse
Features: * Provides a front-view perspective of the Ender 3 v2 * Mounts to the belt tensioning device on the front of the Ender 3 v2 * Made for a webcam with a standard 1/4" camera mount * Provides enough room for the print bed to move freely on...
cults3d
Wanted to mount my webcam between my two monitors at my eye line rather than above/below. Simple design allows for adjustment on two planes after it is stuck to the back on the monitor. My monitor has a sloped back, hence the angle on the arm. A...
thingiverse
Wanted to mount my webcam between my two monitors at my eye line rather than above/below. Simple design allows for adjustment on two planes after it is stuck to the back on the monitor. My monitor has a sloped back, hence the angle on the arm. A...
prusaprinters
Wanted to mount my webcam between my two monitors at my eye line rather than above/below. Simple design allows for adjustment on two planes after it is stuck to the back on the monitor. My monitor has a sloped back, hence the angle on the arm. A...
thingiverse
Remix of DroneDaddy's mount to fit my existing setup from RaffoSan https://www.thingiverse.com/thing:2477180
thingiverse
Remixed from both https://www.thingiverse.com/thing:4702089 and https://www.thingiverse.com/thing:3652452 I have modified the mount so the esp32 camera can mount directly to the camera mount
cults3d
You can download / edit any projects models from github
thingiverse
# Intro This model is based on https://www.thingiverse.com/thing:4702089 I just fine tuned part of the model for better printing experience and better structure. If you are using the original version and find it ok, then just use it. If you...
thingiverse
You can download / edit any projects models from [github](https://github.com/antwal/3dprinters/tree/Models)
thingiverse
A clip on for the CR-6 SE (and perhaps others?) that will allow mounting a webcam on a similar level to the printing My first (non-trivial) 3D design work.
thingiverse
Extra screws and nuts you might need for usage: (1) 1/4"-20 x 1-1/2" bolt (for hinge) (1) 1/4"-20 x 5/8" bolt (for webcam) (1) 1/4"-20 thin nylon lock nut (Optional, but highly recommended) (2) 10-32 x 3/4 bolt (to connect mount to belt tensioning...
prusaprinters
Some of the parts are remixed from the Modular Mounting System https://www.thingiverse.com/thing:2194278 This is for mounting a webcam to the side of your monitor with double-sided tape. It can be adjusted up and down by loosening 1 thumbscrew.</p>...
thingiverse
Some of the parts are remixed from the Modular Mounting System https://www.thingiverse.com/thing:2194278 This is for mounting a webcam to the side of your monitor with double-sided tape. It can be adjusted up and down by loosening 1 thumbscrew. ...
prusaprinters
... because it wouldn't fit into my extrusion rail, so I slimmed it down a bit. It also didn't have the right mount for my camera. ...It will now work with a standard tripod mount style webcam. *Added Left side per request. Category: 3D Printer Accessories
thingiverse
... the original version because it wouldn't fit into my extrusion rail, so I slimmed it down a bit. ... It also didn't have the right mount for my camera. It will now work with a standard tripod mount style webcam. ... *Added Left side per request.
thingiverse
Support for holding Logitech C920 webcam, remixed so that it can be fixed on the enclosing cabinet wall. Prints in place, requires an M3x40 screw to fix the two moving parts. Distance between fixing holes is 25mm, fit for an IKEA Platsa cabinet. ...
thingiverse
... screws, you could put a bracket there without disrupting the frame. Then just secure it with longer screws. There are other places to mount (RaffoSan makes a bracket which clips to the top of the MK3 frame), but for me this was the best solution
thingiverse
... cell phone as well . Basic camera tripod mount screws might be too short. This just snaps into place on the bottom side rails and the weight of camera keeps it there. I printed on its side , so no supports needed . ... I used PLA and no raft .
prusaprinters
It slides into the left side rails of my Ender 3 V2 (should also fit Ender 3/Ender 3 Pro) and has a hole that allows you to screw a 1/4-20 UNC tripod screw to secure the camera. I've included a a 1/4-20 UNC screw that fits my C920, but may need...
thingiverse
... arrive soon amid coronavirus epidemic. Original: I have disassembled a DCS-936L to make it as small as possible, and this is a mount that fits the gut of the DCS-936L on the side of the Da Vinci 1.0 Printer. ... Fit with a M3/4 screw w/o washer.
thingiverse
I mirrored the right side mount to work on the right side per request.
thingiverse
WebCam BSWHD06M http://buffalo.jp/product/multimedia/web-camera/bswhd06m/ BS01+ http://www.bonsailab.asia/about.html Project:http://go-gadgetgadget.blogspot.jp/2016/07/3dbs01astrobox-v09-web.html
thingiverse
WebCam BSWHD06M http://buffalo.jp/product/multimedia/web-camera/bswhd06m/ BS01+ http://www.bonsailab.asia/about.html Project:http://go-gadgetgadget.blogspot.jp/2016/07/3dbs01astrobox-v09-web.html
thingiverse
This is a webcam side mount for the ender 3 v2. if your extrusion has the same holes then it should also work for you. included is a "squaretest" stl so you can check if the holes line up. You can print as one whole piece or you can print the post...
thingiverse
Webcam for vertical mount webcams. ...Compatible with standard gopro mounts.
thingiverse
I will introduce the Webcam mounting device used in my Geeetech Pro B. My Geeetech Pro B uses OctoPrint (RaspberryPi) and works. OctoPrint can shoot Timelapse by connecting Webcam. With a webcam attached to the front or back of Geeetech Pro B I...
thingiverse
mount for webcam for my anycubic mega x there are two models. the swanky wolt (1) is a reinforced version of the swanky wolt in case you have a heavy webcam. The model is meant to be attached using double-sided tape. ... my camera had a standard tripod...
thingiverse
So i took the base from the Modular Mounting System & edited it to fit the adjustable pieces from Webcam mount for Wanhao Di3 / Monoprice Maker Select v2.1. Id recommend making the connecting pieces a bit tighter if your gonna build it higher...
cults3d
... a webcam on the tripod for camera directly. ...So why not to create a mount for webcam? If you don't know how to create a webcam mount, just click my tutorial video (https://www.youtube.com/watch?v=r0qXd9r7mgg). ...The model of webcam is Logitech C910.