webcam stand logitech 3d models

I wanted to be open about the positioning of the webcam, so the mounts attached to the printer were out of the question. With free positioning, I can easily change the position as needed without having to print new parts. However, most mounts are...

Hanging mount for the logitech webcam. ...Used double sided tape to mount to my desk

Mount you Logitech Pro 9000 on your Qidi X-one. ... Thanks to Matthew for permission to show the final print on his pictures.

Mount you Logitech Pro 9000 on your Qidi X-one. Thanks to Matthew for permission to show the final print on his pictures. Print Settings Rafts: No Supports: Yes Category: 3D Printer Accessories

Made this for the Logitech C270, might fit the C310 also. ...I just prefer put my 3D printer cam off to the side rather than mount it to the printer. Can be printed standing up without support. Edit (11/14/18): confirmed to work on C310 also. ...

Just doubled-up this excellent stand for my c270 to add some stability. ... Camera fits in nice and snug and stays put.

I needed a stand to mount my Logitech webcam to my printer so I could keep an eye on the prints. This is mounted to a Folgertech Prusa i3 2020 variant, but it can mount to any 2020 aluminum beam frame printer. It mounts to the rail with two 3mm or...

I can't stress enough how I did basically nothing and pretty much all the credit goes to thatdude902's stand (https://www.thingiverse.com/thing:3057906) All I did was put it in Microsoft 3D Builder and split the middle then merged the top and...

Need one a little taller? This one is 158mm tall. Remixed from https://www.thingiverse.com/thing:3057906. ... Thanks for the great design!

Simple stand for logitech (c270) webcam. ...The indentation of the camera mount must be reground a little

Logitech C170 Webcam Stand

Stand for a C270 Logitech WebCam Print Settings Printer: Prusa i3 Rework 1.5 by EMotionTech Rafts: Doesn't Matter Supports: No Resolution: 0.15 mm Infill: 20% Notes: Designed with 123D Design

So I designed this stand which the folded up base of the webcam fits into nicely and keeps it relatively stationary. Underneath, the two channels are designed to hold pens/laser pointers, which also double as ballast to keep the stand from moving...

So I designed this stand which the folded up base of the webcam fits into nicely and keeps it relatively stationary. Underneath, the two channels are designed to hold pens/laser pointers, which also double as ballast to keep the stand from moving...

I always hated the way my Logitech Webcam Stand was designed, It just wasn't practical for what I needed. I started seeing people using the Mic stands for the webcam and I thought what a great idea, so this piece holds the camera and fits on to the...

by Cpayne3d June 24, 2019 Licensed as Creative Commons, Share Alike, Non-Commercial This project was created to hold a Logitech C270 web cam for my Octoprint server. Other printable camera mounts were either too small, or could not hold my C270...

by Cpayne3d June 24, 2019 Licensed as Creative Commons, Share Alike, Non-Commercial This project was created to hold a Logitech C270 web cam for my Octoprint server. Other printable camera mounts were either too small, or could not hold my C270...

Basic stationary webcam mount for Logitech C920 camera. Three different heights: 45mm 60mm 75mm Hole diamater is 0.250in. for a 1/4-20 bolt. I recommend printing it so the face with the bolt hole is flat on the surface of your build...

Quickmade ajistable stand for my c310 mounted on triple VESA screen mount wirh R36 column. Useful if you can't mount that ones on a screen frame correctly. ...You can use existing on that site models to add tripod mount to that stand.

I wanted to create a simple stand to hold my webcam (a logitech c920) and I couldn't find one to suit my needs so I came up with this! ... Update: Following a suggestion - I 'upgraded' the model, it now has a small hole in the back to allow the cable to...

I needed some form of document camera to be able to digitize hand-drawings reasonably fast.Since they're 60+ Euros and I had a webcam around I decided to build a stand for the webcam.Additional material required:2x40cm 8mm rod/pipe/whatever (for a...

Made a taller version for streaming/recording creality cr-10. Printed with Inland PLA and fit is a little tight, you may want to sand down the inside a little after it prints. ...YMMV

This business card reader stand lets you easily use a Logitech c920 webcam to take photos of business cards or driver's licenses or ID cards. ...You can use a client side webcam OCR page like https://www.imense.co.uk/DL.html to do OCR or PDF417 reading...

I downloaded and printed the initial design and didn't realise that the bracket on my Brio was fixed so it wouldn't fit. So i cut out the front so the bracket will have space as i didn't really want to rip the bracket off. Also as I had to cut away...

I downloaded and printed the initial design and didn't realise that the bracket on my Brio was fixed so it wouldn't fit. So i cut out the front so the bracket will have space as i didn't really want to rip the bracket off. Also as I had to cut away...

Monitor stand mount for the Logitech C270 webcam. ... My specific stand is the WALI Free Standing Dual monitor stand from Amazon https://www.amazon.com/gp/product/B018MU3SAS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 However, it should fit any...

Here is a model and texture study I did pertaining to a Logitech Webcam

a 1:1 webcam, likes are always appreciated!

Tapa per l'objectiu de la webcam de logitech en forma d'auricular Cover for the purpose of webcam logitech shaped handset

Support WebCam Logitech