wera tool check plus pouch 3d models

A Versatile TOOL HOLDER Perfect for Everyday Hand Tools. Engineered with Precision using Fusion 360, Printed with Ease on the Ender 5 Plus. Two strategically placed 0.23in holes in the bottom accommodate dowel pins, while five millimeter C'Bore...

A little holder clip for the dab tool that comes with the Yocan Evolve Plus dab pen, just slide it up the barrel of the barrel of the pen and clip the tool in, never misplace your tool again. ... You may need to adjust your slicer's scaling options to...

Custom tool holder for Ender 5 and Ender 5 Plus to fit all given Creality tools and more! Specifically designed to stay out of the way of your prints. I used two M4 screws about 12 mm tall with M4 T-nuts. Standard 9/64 works too if you get small...

Wanhao's innovative Cocoon Create I3 Plus Tool Holder is a game-changer for makers and DIY enthusiasts alike. ...This clever tool holder keeps all your essentials within easy reach, including precision Allen keys, sturdy snips, the extruder plunger, and...

I was looking for a tool holder to fit my Wanhao Duplicator i3 Plus perfectly. This one attaches securely to the Brace, providing a sturdy base that holds firm in place. ... One can easily mirror it using Cura or any other slicing software if you need...

This is a tool holder for the sapphire plus with acrylic sides. It requires the t-locks that come with the kit to hold the acrylic to the z bearing aluminum extrusion. I do hope to design some clips like what comes with the kit so that everyone can...

... is not 100% horizontal then you end up with a skewed fix. What you need is a simple tool that helps aligning the heat bed support perpendicular to the rails. ... I keep a list of problems/fixes that I have with the Sapphire Plus on my website.

Original Equipment Holder for Genuine Wanhao Duplicator i3 Plus

If your slicer expects inches when you import this, it will be extremely small and you'll have to scale it by 25.4 (or multiply by 2540%) *** This tool is designed to make leveling your Z Axis simple. Snap it onto the Z rods below the X axis, then...

... the bowl and look down inside the column to see the spur gear tabs. Align the tool fingers with those tabs, engaging all six at once, and push down firmly on the tool. ...The spur gear will move a couple millimeters, letting you pull it off the top.

When assembling the Sapphire Plus at some point you get to the chapter "Install the Hot Bed Support". The manual states "Fix it to the sliders on both sides and keep it horizontal and not skewed". What they mean is you have to mount it on the...

This accessory is designed to securely store the tools that come with the Monoprice Maker Select Plus 3D printer. It holds all five sizes of Allen keys as well as the print removal tool supplied with the printer. To attach it to the printer, remove...

... collection. ...It's versatile and handy, making various tasks a breeze to accomplish. I couldn't imagine doing DIY projects or fixing things around the house without it. This essential instrument has definitely earned its place among my favorite tools.

I have tried a couple of waste bins and tool holders designed to fit the Kobra Plus that actually do not fit (clearance issues) so I decided to take a stab at making one. This was designed in OpenSCAD and I am a total noob with 3d design, but after a...

I have tried a couple of waste bins and tool holders designed to fit the Kobra Plus that actually do not fit (clearance issues) so I decided to take a stab at making one. This was designed in OpenSCAD and I am a total noob with 3d design, but after a...

This toolbox holds all the tools supplied by Creality and more: Hexagon wrenches (M5-M2) the extruder cleaning wire the M6 / M5 open-end wrench the M4 open-end wrench tweezers (angled) Tweezers (normal) is my own that I still had :) the Micro SD USB...

I removed the little bucket for the SD card and USB drive since I use Klipper and a Raspberry Pi 4 on my Ender 5 Plus. ... Designed this because over time the original I remixed from lost its grip on the 2040 extrusion and started to slide down the...

Secure your caliper's 16mm shaft to the Printrbot Plus' rails, enabling precise bed leveling. Insert it into the designated slot and attach it to the x carriage rails. Zero the caliper at a print bed corner and measure as you move it around for...

My desing of a toolholder for ender 5(plus), it just snaps on the rails i print it in 3 walls and 20% cubic infill takes about 2 and a half hours,has slots for the stock hex keys the wrenches the spatula the sidecutters and some extra slots to hang...

... files included, one for each side of the object. The tool holder can accommodate various items such as allen wrenches, scrapers, sd cards, micro sd cards, and metal poker tools. ...I added manual supports to certain areas, as seen in the last image.

Ender 5+ Tool holder designed to fit on frame with no screws required. &nbsp;I printed the model as is with no support and 13% infill. ...&nbsp;&nbsp;</p>

There are 6 versions of the design, each with its own unique feature set depending on whether you want to mount it to the left or right side, if you want the front tool hanger, or bit holder. The versions that omit the tool hanger and bit holder use...

The Wall Mount Full is perfect for larger tools with unique depth bases, such as reciprocating saws and vacuum cleaners. To avoid wasting filament on deep bases like the vacuum, I created a wooden spacer that bonds the two parts together before...

... attaching it to the frontal aspect of the two tower arms at the base. ...Next, you'll need to slide your LED display across to either the far left or far right position and then secure the tool holder within the remaining 60 mm of clearance on hand.

... well. Edit: For optimal results, recommend printing one tool at a time if your setup has a slight tilt. ...This will produce two identical parts that can be used together to synchronize the z lead screws, resulting in a perfectly level x axis.

This is my newest tool holder, it is still a work in progress.(As of right now i don't like the design as its very cramped needs work)Print on its side with the USB holder on the top.no supports neededprinted in PLA Let me know how it goes!if you...

I required a variant that could be installed without having to reverse the extrusion, in order to insert the original tool (https://www.thingiverse.com/thing:4198943). So I designed this version which utilizes 2 x M4x8 bolts and 2 x M4 T-Nuts. I have...

Stand and tamper base for use with common 9-prong WDT tools and should also store common sized funnels that fit around a standard size portafilter basket. Sizes available: - 58mm for usual E61 group type machines like...

I made this to hold the tools included with this printer. There is a lot of unused space inside the printer walls, before I just had them laying on the bottom but they could get knocked around under the bed. This holder wedges between some of the...

I made this to hold the tools included with this printer. There is a lot of unused space inside the printer walls, before I just had them laying on the bottom but they could get knocked around under the bed. ...This holder wedges between some of the...