what can be printed with a 3d printer
4593884 3d models found related to what can be printed with a 3d printer.thingiverse
Para ajustarlo al diámetro de tu cohete mide el diámetro de la botella, sumale el ancho del borde del la impresión 3d ( normalmente 0.4mm en cada lado) y aplica ese porcentaje a la escala del modelo en tu slicer . Ejemplo: mi botella mide 90mm, le...
thingiverse
... note is that for people with small printers, it comes with a stern and bow piece. Basically if the completed ship is to big to fit on your printer, you can always print it in multiple pieces and just glue.melt them together when there done printing.
thingiverse
a standalone touchscreen device that can be attached to and operate practically any 3D printer. ...https://www.kickstarter.com/projects/1177632968/activ8-a-touch-screen-device-and-os-for-your-3d-pr/backers www.active3d.co.uk
thingiverse
Little example of a simple pencil holder with 3 finishes in the top: the complete word, sliced flat, or sliced flat with a rim I'm afraid this needs support... ...:/
thingiverse
a control box and base that can be printed on the X1for the X1 i have now included the unit in just 2 bits for bigger printers had a few people say joints where to tight so have opened them up just a tiny amount [EDIT] i have changed a few small...
thingiverse
all you guys and gals out there that are mad they now have to print a new better set you can blame (thank) Rob Zarfas from the FB "Tronxy X3, X1, X5 3D Printer Users (All models)" group it was his suggestions and ideas that helped me draw this up...
thingiverse
A Pistol Model, that can shoot with Rubber Bands. ...I Printed this with my Ultimaker 2+ and 0.8mm Nozzles :)
thingiverse
That plus a bit of a brim on the pieces with sharp corners (the top pieces especially) seems to have come out quite well on my heated-bed but not enclosed printer. The pieces are held together with superglue, and retain the little index peg holes...
thingiverse
Here is a show video http://www.youtube.com/watch?v=Sg1CU6kxzb4 online store:http://www.dhgate.com/wholesale/store/ff80808136bfebe50136d41f502e7afe_0.html http://www.aliexpress.com/store/822821 haoe3d@live.cn
cgtrader
A watch movement that can be used for 3d printing .Modeling with industrial 3d software . ...
cults3d
Mars III Rocket It can be printed with no supports and no infill. ... Printed with a .28mm layer height and 3 layer wall.
thingiverse
Mars III Rocket It can be printed with no supports and no infill. ... Printed with a .28mm layer height and 3 layer wall.
prusaprinters
Mars III Rocket It can be printed with no supports and no infill. Printed with a .28mm layer height and 3 layer wall. Print Settings Printer: Artillery Sidewinder X1 Rafts: NoSupports: Yes Resolution: 0.28Infill: no Category: Sculptures
thingiverse
Paint brush holder with modular legs that can be printed sideways for strength
thingiverse
here's the center spider from the Spiderman costume pulled it out of a dingbat typeface of movie logos and symbols
thingiverse
Can be printed with just one perimeter.(bottom layers should also be enabled) It contains pellets that are build from the bottom but cannot fall out. This stuff can also be found o-jasper/various_physibles at github. License See at the top of the...
thingiverse
- NOTE: 5'8" would be 28.79mm at 1/60 (5' per inch) scale (5'8" = 68" = 1.7272m = 1727.2mm; 1727.2mm/60 = 28.7866666667) ("28mm scale" means 1/60 scale, since 28mm would be the level of a person's *eye* [1.68m = 5.51 ft = ~5'6"]) Model was short...
grabcad
Robotics teaching.Anthropomorphic robot to be 3D printed with minimized supports.Base with NEMA 17 stepper motor and gears.Two 20Kg / cm servos at the base to increase the lifting load (about 300g).20Kg / cm servo on the arm and wrist.Two 2Kg / cm...
youmagine
In particular I am working on a way to fix the iris in various opening diameters. As with the original design I have used plywood for the case, and am using the exact same electronics (although I have had better experience with Nema motors and...
grabcad
Lorick ready to be 3D printed with feary light to be inserted
prusaprinters
This is my first modle and it's not too good, I made it on tinkercad which you can probably guess. I think this needs supports for the nozzle and the tube where the fillament goes through. ... </p>
thingiverse
I haven't been watching to see it happen, but when I look at the print, there is a clear line at exactly 40mm up where there is a slight layer shift. There is also a lot of stringing and general nasty print quality. This happens again at 80mm on the...
thingiverse
after you have a good stone you downlod the file and print a handle/ then you put the stone in a pan on the fire untile its hot, cerfully lift it and push it in the right place, after its in the spot you want it, put it under water and it will stay...
thingiverse
... it to put in a box that doubles as a dice tray. (gift for a friend) Can be easily covered in some kind of stickers or implemented in something else. ... I also covered inside of it with felt to make it quiet when used, suggest doing it also :)