whetstone with angle guide 3d models

FILAMENT GUIDE WITH PC4-M10 FITTING (THREADED) by DAR01. This allows you to fit the spool holder facing forward on an Ender 3 v2 3D printer and prevents the filament bending around the lead screw by using a reverse bowden tube to guide the filament...

Super minimalist and max functional design now stronger, compatible with more cameras, better angle control, and no need for supports. ... Components Used and Tested Raspberry Pi Zero W 1.3 - ANYWHERE :p Pi Camera V2 Clone -...

I Design My Own Mind-Blowing Spool Holder with a Flexible Filament Guide! This is a Major Upgrade! ... I'm Including the Source Code, and You Can Use It with Your Favorite CAD Software, Like FreeCAD!

An alternative Filament guide for the Ultimaker 2 with beared wheel. No more ticking sounds from the feeder... ... Instructions Print at 100% All you need is a bearing with a 12mm hole, 28mm outer Diameter and 8mm height.

I slightly extended the mount upward to fit my cup holders more securely and I closed the jaw angle (to parallel) to get a good grip on a gel cased 70mm wide phone (Moto G7 or Samsung A51) Print Settings Printer Brand: Prusa Printer: Mk2.5sRafts:...

'I recommend spraying the finished print with hammered varnish, then it looks like the real thing !!!! ( Just like my table hardware ) You can of course scale the size but as they are, they are enough for 10 Cm deep wooden shelf boards. Now...

'I recommend spraying the finished print with hammered varnish, then it looks like the real thing !!!! ( Just like my table hardware ) You can of course scale the size but as they are, they are enough for 10 Cm deep wooden shelf boards. Now...

This time with angles at each corner instead of round shape. Additional 2 simulated sode panels and rear window. Same fitting than the previous one using existing holes of the body and screws direcly on the topper body. In addition a roof rack full...

Kawobei's revamped Slow Stick Motor Mount features a modified thrust angle of 3 degrees down and 3 degrees to the right.

Frame Braces and Supports for the Tevo Tarantula - Adjustable Angle and Distance. ... Required Components: * A threaded M6 rod * M4 bolts, nuts, and T-nuts * M4 screws

Remix of https://www.thingiverse.com/thing:4779198. ... The distance between the fasteners is increased. redesigned the clamp to adjust the angle of a light

The only additional parts required are 2 drywall screws with wall anchors if needed, and a V-Roller / POM Wheel (The standard 24mm ones Creality Printers and most others use) for the filament guide. ...You'll also need an M3 screw plus a few M3 washers...

I've Replaced the Filament Guiding Hook with a Small Housing for a Filament Filter, Making it Easier to Keep the Filament Clean from Dust and Other Debris. Simply Fill this Housing with a Piece of Foam to Ensure Optimal Performance. Printing this...

I found that with my direct drive Ender 3 the filament was catching on my cable chain so I made this guide. These are 2 models you can print, one for a filament guide and another for a PTFE guide for bowden tube systems. No supports are needed for...

The design is currently on my Hoverthings Flip FPV Pro model, but it should work well with almost any multirotor equipped with a flat mounting plate. This innovative mount features a convenient slot for securing a zip tie in the right spot over the...

In case Thingiverse decides not to display the photos: https://drive.google.com/drive/folders/1NFpZvGRH4Tua7bTN35fGP1Boa4NUzYso This remix of EaziG's Keyring Phone Stand With Adjustable Angle has been modified to remove an awkward design element. The...

This is a drill guide for 3 and 5 mm drill bits and using self-lubricating bearing for reinforcement. It suitable for drilling 90 and 45 degree angle. Bearings are very cheap e.g. ...on Aliexpress:...

This device features a filament guide equipped with a wire presence sensor and a three-pin plug socket that can accommodate a power cord, providing crucial support to the extruder.

This is a filament guide equipped with a 6800 bearing so that there is as little constraint as possible on the filament depending on how new the spool is. ... https://youtu.be/uLcfhVXyk_Q

this is an edge cutter with guides, so you don't need a ruler to use it Waiting for your remixes, source files included! ... you'll need 2 m2 nuts 2 m2 screws chineese razor blade

This is simple, easy print, rigid filament guide with m10x1mm thread for ptfe tube mount. I was tired of spool getting tangled up, dragged and eventually falling onto the printer so I made this. Thats it. ...:)

I created this design specifically for the filament guide that's included with the all-in-one upgrade STL file. ...The original dovetail component had significant flaws, resulting in air pockets forming during prints near the extrusion tabs.

This is simple, easy print, rigid filament guide with m10x1mm thread for ptfe tube mount. I was tired of spool getting tangled up, dragged and eventually falling onto the printer so I made this. Thats it. ...:)

A simple filament guide trough for an IKEA Lack enclosure, crafted with ease. ...Simply drill a hole of 13mm diameter, then gently insert the part from both sides until it clicks snugly into place.

The motor is angled for better clearance and designed to fit into http://www.thingiverse.com/thing:12151 without hitting the sides. However, it requires a universal joint to alter shaft angle and cork shims may be needed for packing the joint. ...Test...

Added adjustable stand because in my case the screen stays on top of the printer on my desc and the angle was not good for me for viewing. Added top and both sides mounts. Keep in mind that the stand also can be rotated and give more mounting...

This device is engineered to accommodate a board camera with a ~12x12 mm PCB and provide adjustable angles from 0-45 degrees. To secure it to the frame, four m3 screws and nuts are necessary. Additionally, hot glue can be used to firmly attach the...

I use an Xbox controller as my main controller with my Dreamcast (coupled with the Brook Wingman SD) and I recently built a controller to more closely match my DC, except the guide button looked out of place. I printed the pieces of the guide button...

... I introduced a PTFE tube to provide some stability. However, the tube itself began to move around, defeating its purpose. In response, I modified the Axis Screw with Guide to incorporate a solid section that includes an opening for the PTFE tube.

Instruction for Assembly: Rear light consisting of the following parts: Housing - 01 qty (PC + ABS material) Lens - 01 qty (PC clear material) Light guide Lower - 01 qty (PC red material) Light guide Upper - 01 qty (PC red material) Reflector - 01...