whetstone with angle guide 3d models

I wanted to increase the height of the model by Xavier_57 and at the same time designed a filament guide slot to sit between the screen and frame. I have also included spacers for the original perspex i3 Pro B screen to substitute for the laser cut...

I encountered a problem where my filament spool was coming loose and rolling excessively, so I designed a filament guide that fits snugly into the bottom-most holes on the spool holder. This solution prevents the filament from becoming dislodged as...

A precision-crafted filament guide featuring a robust 608zz bearing. Installation is effortless, as no screws or nuts are required to secure the bearing in place. However, two M5 x 8/10 screws and two M5 t nuts are necessary for mounting purposes. ...If...

I've just added an extension onto it to act as a filament guide. The extension is twisted a bit at the end so the filament doesn't get bent too much when the extruder is at the highest Z-value. ... Included is the complete stl, and also the...

I edited the arm from here https://www.thingiverse.com/thing:4745849 for handling better the filament, also avoiding unwanted slip by cutting the slit at 45 degrees.And using the frame clip from https://www.thingiverse.com/thing:4321023.Added an...

I edited the arm from here https://www.thingiverse.com/thing:4745849 for handling better the filament, also avoiding unwanted slip by cutting the slit at 45 degrees.And using the frame clip from https://www.thingiverse.com/thing:4321023.Added an...

Once installed, access the comprehensive guide to generating 3D printable molecular models by downloading the accompanying PDF file located in the Thing Files section. ...For the most up-to-date version of this tutorial, visit...

I crafted this to secure itself to the lower right corner of the i3 Mega frame, serving as both a mounting base for the raspberry pi case and a precision guide for the filament. After testing it out over a couple weeks, I can confidently say that it...

... S2 dry box. ...I use the bowden configuration when printing hydrophilic filaments like Nylon.  The M10 hole is mounted at an angle to reduce stresses and provide a natural path to the extruder. ...You can self-thread in any generic PC4-M10x1.5 fitting.

I carefully selected two designs from hundreds of filament holder/guide designs available online and merged them to meet my specific needs. ...I purchased all necessary hardware from Amazon: * 8mm x 500mm rods can be found at this link:...

Mounting Clip for Level 2 EV Charging Cable, Compatible with J1772 Standard, Secures to Wall with Large Downward Angle, Optimizes Siemens Charging Handle Position for Straight-Up Use.

http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions Using the following settings: Fan Speeds: D Fan 2 = 80, D Fan 1 = 40, L Fan 2 = 74, L Fan 1 = 34 Manual Angles: Azimuthal Manual = 0, Lead Angle 1 = 30 Geometric Parameters:...

Remix of https://www.thingiverse.com/thing:3102626 i added a guide for X energy chain like: https://www.thingiverse.com/thing:2550208 I use this Hotend...

This is a remix of the Filament Guide for Creality Ender-3 or CR-10, https://www.thingiverse.com/thing:3052488 from Holspeed. I added a Filament Runout Sensor to the design. The switch must conform to DIN 41635 standards, featuring a roller lever,...

* 2 M2x12mm screws * 2 M2 nuts * Wire and connectors for Raspberry Pi pins The model has extended walls to guide the switch arm, but the pictures show shorter walls. This may cause filament to jump out to the side. However, this shouldn't be a...

This guide is attached to the X axis motor so that it does not rub against anything (you just have to loosen the bearing screw a little to mount it, it is not necessary to remove it completely). It also has a built-in foam filter to clean the...

http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Options: Wall thickness: 2.5 Zero motor rotation Fan diameter 2: 4.3 Fan diameter 1: 3.4 Magnet angle: 45 degrees Cone angle: 100 degrees Fan 2 speed: 50 RPM Fan 1 speed: 30 RPM Nail...

http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions Using the following options: fan_speed_mani = 0 dual_fan_size_2 = 3,2 dual_fan_size_1 = 3.4 turbine_wall_thickness = 2.5 angle_of_mani = 45 cone_angle = 100 dual_fan_size_2 =...

Customized Version of Thingiverse Project Created Using Customizer Application at http://www.thingiverse.com/apps/customizer/run?thing_id=735038 **Instructions** Configure Parameters with These Settings: Pipe Height: 1 unit Main Fan Radius: Off Cone...

Same part but with sloped filament entry

fingerboard mold with popsicle shaper and fishtail shaper

Designed for Ender 3, Ender 3 Pro and Ender 3 V2. ...You can use with 625ZZ bearing with V-Slot.

I make a mix from a lot of project with add a protect for filament arround the Z axe. ... Print it with support!!

Used for Bowden and reverse bowden setup on an Ender 3 MAX with a BMG extruder.

Slotted version for adjustability, print with atlease 50% infill use m3 bolts and nuts

I used this in conjunction with TUSH - Adjustable with base - https://www.thingiverse.com/thing:2257015 This design was crafted using Tinkercad, and you can edit it online at https://www.tinkercad.com/things/di2w3lwgtsP

I had to move the filament channel about 4mm closer to get it to line up with my Ender 3.

It's crucial to remember that you should place the spacer on the mount prior to adding the bearing, then secure everything with the cap and finish by screwing it into place using a 5mm screw with an M1 or M2 thread - any screw with a 2mm diameter and...

http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions: Using the following settings: Lateral Maneuvering Arm Length (l_mani1) = 0 units Azimuthal Manuevering Angle (az_mani) = 0 degrees Nozzle Angle (n_angle) = 50.1 degrees...

Human: Customized Version of Thingiverse Design Created Using Customizer Tool from Thingiverse.com http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions for Assembled Model Choose the Following Options for Customization: Fan...