wifi dish antenna 3d models
37092 3d models found related to wifi dish antenna.thingiverse
I am not sure about the impedance matching of this antenna, I am not an expert, however, it works pretty well, I made a quick test tonight and was able to see about 20 wifi Access points just by pointing the dish in one general direction without...
cults3d
on a 2.4GHz Wifi Dish Antenna Uses a M3 x 30mm SHCS to secure it to the feed. Reflector oriented as shown results in Vits. of ~120. ... Print as oriented in STL (standing), no supports needed, but brim suggested - material and layer height as you wish.
thingiverse
on a 2.4GHz Wifi Dish Antenna Uses a M3 x 30mm SHCS to secure it to the feed. Reflector oriented as shown results in Vits. of ~120. ... Print as oriented in STL (standing), no supports needed, but brim suggested - material and layer height as you...
grabcad
The antenna has only outer design, it doesn't contain any electronic parts & other inner assembly parts.
pinshape
Antenna dish model for 3D printng. ... Units: millimeters Length: 132 mm Width: 122 mm Height: 154 mm
cults3d
made this wifi dish for wifi usb adapter. it comes as 5 pre-assembled part. you can print all at same time, or one at a time. the dish comes with base to hold it up, as well as support brace for adapter. it is designed so that front and back dish sit...
thingiverse
A 3D printable version that looks a little less redneck like the aluminum can version (https://lifehacker.com/5839243/use-an-aluminum-can-as-a-wi-fi-extender). ...Try wrapping tinfoil around the dish part of the extender.
grabcad
17 dBi wifi antenna, for more details please visithttps://ypylypenko.livejournal.com/56724.html
thingiverse
A mount for Teltonika Wifi antenna. To hole it upside down or on a wall. ...Requires one screw.
thingiverse
... WIFI cards in the back of the computer. ... Most PC cases are metal and block WIFI signals. Use this with RP-SMA extension cables to mount WIFI antennas away or above the computer. ... It might require double-sided tape to keep the WIFI stand upright.
grabcad
This antenna is used for many of our products that have WIFI built in. ...I modeled it to create better looking assemblies and renderings of our products.
grabcad
It allows you to protect the place where you insert the wifi antenna in case you don't put it in.
thingiverse
This is a simple mount I made to extend wifi antennas from my PC. Can be placed on a desk or mounted on a wall. ...Antennas can rotate and be placed in different orientations.
thingiverse
I updated my wifi card in my Dekstop PC to an AX210NGW Intel card and I was not receiving a great signal with my previous antennas. Upgraded to these 8 dBi antennas and designed a base to attach them to. It's nothing special, but it does what I...
myminifactory
... the antena to anything with a large zip-tie / Cable-tie. the Mount Lock I designed specificly for mounting the bracket on my boat. You can see a full description on the install on my blog. http://irialkennedy.com/boat-wifi-long-range-antenna/
thingiverse
... software coded in C#). ... This system is made up of 3 cases and we needed wifi antenna holder so they stay motionless when travelling. Voila Designed for : -Screw hole radius (head) : 2mm -Wifi antenna radius : 4mm Hope it can be useful for you !
prusaprinters
WiFi antenna holder for 3 antennas with magnet (20x10x2mm) insert. Magnets: https://www.aliexpress.com/item/4000833540143.html Antenna cable: https://www.aliexpress.com/item/32232523600.html
thingiverse
This was designed to keep the antennas parallel on a D-Link dual-antenna wifi AP. Instructions You may need to adjust the size/spacing of the holes to fit your AP. As is, these are 6mm holes spaced...
thingiverse
... i found the nut i'm using in an old crate of nuts. The ricorée antenna is a DIY project to build a 2.4ghz wifi antenna out of a can box, more information (in french) here : https://antenne.ooreka.fr/fiche/voir/505011/fabriquer-une-antenne-ricore
thingiverse
You will need extension cables for your Wifi card, Mine is by intel and these are the cables:...