wilson ii 3d printer review

So, as a starting point, I chose to use the Wilson II/Prusa design as published by Marty Rice www.thingiverse.com/thing:1086101 . I named my printer WWIII (Weber-Wilson III). My printer is basically the same as the original, but with a 300mm x...

Improved X-axis Carriage, Idler, and Motor Mount for Wilson II 3D Printer. Enforced and reduced play which greatly reduced vibration and accuracy. Linear bearing in Carriage is fixed by screws and nuts. Linear bearing in Idler and Motor Mount are...

GT2 Pulley and uprated X & Y Tensioner for Wilson II 3D Printer Effectively improved the ripple caused by the mismatching of GT2 belt and original pulley. Pulley can be used for any 3D printer. Uses 2pcs MR84 bearings in the pulley. Support is not...

This is the Wilson II, it is a new design based on the Wilson TS. Some of the design changes are: All smooth rods upgraded from 8mm to 10mm. Z axis threaded rods replaced with 8mm lead screws. Upright frame consists of two sets of vertical beams...

... X aluminium beams with 2 screws per connector. ...This will allow much stronger build and easier orthogonality achievement. Print Settings Printer: Customized prusa i3 Rafts: No Supports: No Resolution: 0.24 Infill: 30 Notes: Printed in PETG at 235°C

... the TV animated series Dungeons & Dragons. ...Revised character height and hand size. Review II - Full piece and divided into four parts.  Recomended print the Hair and Gem using Raft. The part can take off from the base if you did not use raft.

Wilson II plastic parts Print Settings Printer: Anet A8 Rafts: Yes Supports: No Resolution: 0.1mm Infill: 75%

This is the Bowden Mount for a Wilson II printer. I've included the OpenSCAD file along with the STL files for the mount and clamp. This is a straight replacement for the direct drive extruder mount that comes with the Wilson II. You will still need...

Wilson II 400x400 Bed Y Carriage This is UNTESTED For joined 4 x 200x200 Hotbeds together This is specific to a Wilson II design and bolts to a printed Y axis bearing carriage.

This is a remix of the Wilson II printer, to convert it to using 8mm rods and bearings. I've also added ziptie channels to the X-Carriage. The Z Top and Motor files should be mirrored, your slicer should be able to do that. You will need all the...

... it stiffer. Print Settings Printer Brand: RepRap Printer: Wilson II Rafts: No Supports: Yes Resolution: 0.24 Infill: 20 Notes: Does not print solid automatically. Use several walls. ...How I Designed This Edited the original .step file in solidworks

Changes from original Swapped Extruder and Stepper sides Moved BLTouch mount to be more in line with hotend Resized mount holes to M4 hardware (to match Wilson II carriage) To do: Tweak M4 holes/nuts for proper fit Check BLTouch mounting holes Add...

This 3d printer will be in a classroom and I don't want curious hands accidentally touching something that might kill them. The enclosure needs supports and the mount does not. Attach the mount to a 2020 extrusion and attach the Arduino Mega with zip...

A Mount for the BL Touch Z Sensor that will bolt onto the stock Wilson II Extruder. Happy Making! ...Print Settings Rafts: No Supports: ...

This is a fan duct for the Wilson II. You need to measure the distance from the center of the fan hinge on the extruder to the tip of the nozzle. Measure vertically and horizontally. Enter those measurements as nozzledistanceV and nozzledistanceH....

... line up better. Original bracket is the "Green" one the "Red" is the one that i produced you can notice the holes were shifted just slightly. Power supply model: JCPower JC-360-12 Print Settings Printer: Wilson II Rafts: No Supports: No Infill: 25%

This is a modification of the X-Axis ends for the Wilson II to allow for the use of the Tr8*8 anti-backlash nuts from RobotDigg. Many thanks to MRice for including the SCad files to allow for modifications. I've also included the modified SCad file...

This is a part that allows for the use of a radial/blower style fan for the Wilson II fan mount. It can be printed with support only needed for the inside where the fan meets the duct and the arm for the fan. Inside that circle of the duct prints...

Assembly whole mechanical components of the Rebel II

... and the leadscew nut in place attach a couple of these to assist in lining up the leadscrew and motor before tightening the motor screws. Print Settings Printer Brand: RepRap Printer: Wilson II Rafts: No Supports: No Resolution: 0.2 Infill: 50%

... fit. ...https://github.com/mjrice/Wilson2 Added Marlin 2.0.x Config.h file as example of how to setup deploying the Rack and Pinion. Print Settings Printer Brand: RepRap Printer: Wilson II Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 50%

I made custom mount for Wilson II for support Titan Extruder and BLtouch. ...Fits and works perfect

The hole is 2.5mm Added 2018: cable_chain_brackets_step.zip STEP files My Printer I'm using 21 8x20 links for Z 24 8x10 links for X 22 8x10 links for Y Print Settings Printer Brand: RepRap Printer: Wilson II Rafts: No Supports: Yes Resolution: 0.2...

Overview I have been trying to improve print quality of my Wilson II so I'm attempting to replace the direct-drive extruder mounted just above the hot end with a Bowden extruder. The main goal is to move the extruder motor to the frame and off the...

Wanted to extend the X travel of the Wilson II and needed to space the bearings out on the bed to better support the platform. Ended up at 9in due to my current printer's limitations. Had to load the STLs into CAD and break it apart. Took the main...

Titan Aero mount for Wilson II X carriage. ... Slim pickings for Titan Aero extruder mount that is compatible with Wilson II X carriage which uses 10mm rods. ... I liked Mr.Damage's design and he was gracious to upload the Step files.

Part of my Fuel 3D Scanify Review.

Part of my Fuel 3D Scanify Review.

If someone wants to use this on a non Wilson II Printer it will work fine but if you can give me some dimensions I can offset the bracket up which will give you some Z Axis height back but also give you clear access to the adjuster screw. Hole pitch...

This is my solution for using a PC Power Supply to run my Wilson II. Can be used on any printer using 20 x 20mm extrusion frame. I used this guide to make my Power Supply system: http://reprap.org/wiki/Choosing_a_Power_Supply_for_your_RepRap You will...