wire extruder 3d models
136876 3d models found related to wire extruder.cults3d
Blower, Filament End Sensor plus Extruder Trigger for B-Velta
thingiverse
Support to guide the wiring of extruders out of bed in the Geeetech A10M. ... Soporte para guia el cableado de los extrusores fuera de la cama en la Geeetech A10M
cults3d
The rods at the front of the shelf (that extruder brackets rest on) is 1-5/8" OC.I'm using 3/8" threaded rod 3-5/8" long as the axle for the spool arm. The spool rack and extruder bracket were printed on my CR30, 0.6 nozzle - 0.3 layer height. The...
thingiverse
The rods at the front of the shelf (that extruder brackets rest on) is 1-5/8" OC.I'm using 3/8" threaded rod 3-5/8" long as the axle for the spool arm. The spool rack and extruder bracket were printed on my CR30, 0.6 nozzle - 0.3 layer height. The...
thingiverse
Get your wire tube attached to the side of the extruder where it should be. This is a work in progress. It works find as is, but could use some improvement attaching to the extruder without any glue or screws. Thats the idea, no glue no screws,...
thingiverse
During the printing the wire from Extruder Stepper is moving to much. It´s the matter of time, when the wire will break. ...This thing prevent this Problem.
thingiverse
I designed this to hold the wires going down to the extruder as well as the fan wiring. ...It mounts in place of the spacer for the led board and could be used other places as well.
thingiverse
Remixed the P905X Extruder Wire Support to fit on the normal P905 single extruder version. ----------------------------------------------------------------------------------------------------------------------------------- Note: UPDATED AND...
thingiverse
This is a radial fan extruder cable guide i made. you will have to rotate this thing to be flat in your slicer. ...still figuring out fusion 360.
thingiverse
This secures the four connectors and cleanly routes the wiring to the main bundle. 1) The mount is secured to the M2's metal motor mount with 2x M4x16 bolts. 2) The box is secured to the mount with 2x M3x18 bolts and 2x M3 captive nuts. 3) The arm...
thingiverse
Simple holder for the extruder wiring to keep it from moving on the extruder.
thingiverse
I noticed the extruder wires were rubbing on the lever after changing the extruder lever so I made this holder that uses the zip ties that come with the Ender 5
thingiverse
I had the wires going into my extruder stepper break due to the fatigue caused by them wiggling back and fourth. This part uses the screw hole in the stepper that the extruder body doesn't use. ...I used a 3x8mm screw to secure it and two small zip ties...
thingiverse
On the PowerBelt3D Zero printer, the wire bundle from the extruder to the controller sometimes slips around and interferes with the X end stops. This small part snaps in place to keep the extruder wires from moving around. ... It also functions as the...
thingiverse
This extruder cover is the main support for the large loom of power and thermocouple wires connecting to the extruders. This printable project installs on top of the extruders using the original mounting screws. It is a minimalist wire loom support...
thingiverse
No more wire clipping to the endstop. ... Designed with Onshape.
thingiverse
After two breaking wire because of movement, I put this support to matain extruder wires
thingiverse
Two piece unit that clips the two filament guides and the extruder wiring together. ... No more watching the spiral wrap drag on case side.
thingiverse
This little piece provides support for the print head wiring harness by clipping it to the filament guide tube and keeping it from flopping about. ...
thingiverse
These little brackets support the wiring for the print head using the bowden tubes as anchor points. ... I'm using them on a Qidi Tech-1 but they'll probably work with the Flashforge Creator or any of these other cloned printers.
thingiverse
Based off of Lawsy's design, I remeasured to fit the Bulldog motor EDIT 1-20-15: Wire guide opening has been lowered 5mm for use with Solidoodles. If you use a Solidoodle, be sure to download the correct file. Skp file has been added as well.. ... ...
thingiverse
FlyingBear P905X Dual Extruder Wire support. No need to remove all of the wires to install. Just clip onto the print carriage and slide wires into support. ...Then zip tie to keep the wires in place.