wire hole cover 3d models
491272 3d models found related to wire hole cover.thingiverse
Cover for the wires and the hole from overheadlamps. I usually struggle with the delivered plastic cover of overhead lamps, as they are mostly thin and cheap made they never stay where they're supposed to. So I designed this Threaded cover. It...
thingiverse
A simple plug designed to keep wire tidy on a desktop with wire hole.
thingiverse
... ... The original design kept popping out of the hole as the wires moved around, and also didn't quite seat the wires properly in relation to my printer, so I took the basic design and rebuilt it in OnShape. _Note: Designed for QIDI Tech 1 printer.
thingiverse
Wire Hole Cover used to finish a rough hole... cool!!! ... Visit my Youtube Channel: https://www.youtube.com/channel/UCQB4RRae63k2nnA1YA39yZg Visit my Blog: https://clmake.home.blog/
myminifactory
Inspired by the cable hole plugs on my desk, I drew up this two-part hole plug and cover to plug the holes and give it a cleaner, less obvious look. This is designed for 26mm diameter holes, but can be scaled up/down to fit other sizes. The holes...
thingiverse
Parametric cover for a holes you may drill for mains wires through table tops, cupboard walls and so on. The idea is that you may need a fairly big hole to enable the plug the go through. Which would leave a big, ugly and impractical hole, unless...
thingiverse
A simple thing, to organize the wires passing through these huge wholes on office desks. ...The idea was to keep the wires from falling into the whole when you are not using it and, cover the whole.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wire_hole_offset = 20.0 hole_dia = 77 t_starts = 1 have_lower_frame = 0 tol = 0.7 wall = 1.2 hole_depth = 9 wire_dia = 8 lip = 3 t_pitch = 1.75...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wall = 1.2 have_lower_frame = 1 t_pitch = 1.75 hole_depth = 23 framewall = 4.0 t_starts = 6 lip = 5.0 wire_dia = 12.0 wire_hole_offset = 20.0...
thingiverse
This Trailer Hitch Receiver Cover has a slit in the cap to allow the plug and some additional wiring to be pushed into the receiver so it doesn't hang down and get destroyed. The cover should be snug but easy to put in and take out. Also has two...
cults3d
This Trailer Hitch Receiver Cover has a slit in the cap to allow the plug and some additional wiring to be pushed into the receiver so it doesn't hang down and get destroyed. The cover should be snug but easy to put in and take out. Also has two...
prusaprinters
With the basic installation we had done the wiring was always falling out of its various hiding places or places we tuck it. This Trailer Hitch Receiver Cover has a slit in the cap to allow the plug and some additional wiring to be pushed into the...
prusaprinters
With the basic installation we had done the wiring was always falling out of its various hiding places or places we tuck it. This Trailer Hitch Receiver Cover has a slit in the cap to allow the plug and some additional wiring to be pushed into the...
thingiverse
Customized version of http://www.thingiverse.com/thing:1324924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of http://www.thingiverse.com/thing:1324924 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
This thing was made with Tinkercad. ...Edit it online https://tinkercad.com/things/any1DMbt5xZ
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
thingiverse
Customized version of https://www.thingiverse.com/thing:1324924 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1324924
cults3d
Well this is a odd size for a wire hole in a table. ...I needed a small hole just for two wires and covered it properly so I made a proper 38mm wire hole cover for table top / side.
thingiverse
Well this is a odd size for a wire hole in a table. ...I needed a small hole just for two wires and covered it properly so I made a proper 38mm wire hole cover for table top / side.
thingiverse
I designed this to cover a hole i drilled into the floor of my boat so that I could run a couple of wires into the boat but didnt want to leave a visible hole or allow water easily in. After printing, I added some marine sealant around edges to...
thingiverse
Wire cover for running small cable or wire through a wall or cabinet. ...My intent is to use it on an RV to cover the outlet and seal with silicone on an antenna installation.
thingiverse
I needed a cover for the led-driver and wires in my spotlight installation came up with this. about 200 mm high, fits in my anycubic i3 Mega, but check the cabling from printhead at max height before printing... ... I printed with PLA Z at 0.2
thingiverse
... tape and attached it to the rug. It would work with wood too. I used around 140 g of PLA+ to cross my living room, much cheaper than commercial wire covers. ... Remix ideas: enlarge the surface or create an inner aperture to fit round cords.
prusaprinters
... <p>This was my first real try in developing something in OpenSCAD. I am learn-by-copying kind of guy, so I collected all kinds of designs and learned how they did solve things like the chamfer to slide the cover on. Category: Decor
thingiverse
Keystone Jack for a wire to pass through. ... I had a wire that powers a coaxial cable splitter inside of a wall. I wanted a tidy way to allow this wire to pass in to the wall. The hole in the Keystone Jack is 4mm x 2.5mm. ...