wire hole 3d models

This is a Wire Hole that can be inserted in a 2" (51mm) hole on a desk top or back or in a wall for easy wire feeding. It can be screwed in or glued in. I will often use latex caulking to hold them in drywall. ...The outer ring can be made longer if...

http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: framewall = 5.0 hole_depth = 30 t_pitch = 1.75 hole_dia = 70.0 t_starts = 6 wire_dia = 40.0 have_lower_frame = 1 tol = 0.7 lip = 10 wall = 2...

Keystone Jack for a wire to pass through. ... I had a wire that powers a coaxial cable splitter inside of a wall. I wanted a tidy way to allow this wire to pass in to the wall. The hole in the Keystone Jack is 4mm x 2.5mm. ...

It keeps foriegn objects from dropping into the bottom of the printer and also helps keep the wires orderly. I built it with ABS and 100% fill. Note: Please check the connector and wires to the build plate heater. While building this, I noticed...

This is a 90 degree guard designed to protect a drilled hole against rain. suits a maximum of 20mm diameter hole but can be scaled accordingly. ... This will only protect against light rain, it will likely not protect against stormy situations so it...

A simple plug designed to keep wire tidy on a desktop with wire hole.

Vstab with wire hole (for camera) for Titan Falcon: https://www.titandynamics.org/3dhangar/p/titan-falcon

http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: t_pitch = 1.75 wall = 2 t_starts = 6 hole_depth = 30 wire_dia = 40.0 framewall = 5.0 have_lower_frame = 1 tol = 0.7 wire_hole_offset = 20.0...

http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: t_starts = 6 wire_dia = 40.0 hole_dia = 70.0 framewall = 5.0 hole_depth = 30 have_lower_frame = 1 wire_hole_offset = 20.0 t_pitch = 1.75 tol =...

This is a cover for the wire hole of a computer desk. There is a place for a momentary switch to be mounted with two M2 screws + nuts. The cut-out is meant for cables you want to run through it. The switch is a typical momentary switch __without a...

Cover for the wires and the hole from overheadlamps. I usually struggle with the delivered plastic cover of overhead lamps, as they are mostly thin and cheap made they never stay where they're supposed to. So I designed this Threaded cover. It...

Installed some pot lights in my wardrobe the other day and was left with some unsightly holes I had drilled to route the wires. Inspired by the cable hole plugs on my desk, I drew up this two-part hole plug and cover to plug the holes and give it a...

THIS IS CAP THAT GOES ON LITHAPHANE CHRISTMAS BULB. ...IT HAS CONVENTIONAL SPRING HOLDER AND HOLE FOR WIRES.

Parametric cover for a holes you may drill for mains wires through table tops, cupboard walls and so on. The idea is that you may need a fairly big hole to enable the plug the go through. Which would leave a big, ugly and impractical hole, unless...

... factor of nine to maximum size for a 200x200mm bed. ...Also added a hole for hard wire wall plug. ...I also made a T-10 socket for either LED or bulb and a bottom cap, I will make them available in My Designs .http://www.thingiverse.com/thing:1337872

i made a hole for those that use the HDMI screen/monitor and power cable for your Pi.

A fully customizable, 3D printable corner shelf, for interior or exterior angle corners with optional rear hole for inner corners. This design allows you to choose the radius, angle, thickness and amount of bevel. You can also customize the size...

Will update image once I've printed this out.Update: Made the hole square to match the theme of the rest of the “straight edges” of the fountain while also allowing it to stay bigger. Added 2 more styles to allow for cable to come straight out the...

Here is a shutter for wire hole of 50mm. ...There is 2 versions depending the diameter/number of the wires you want to go through 1- 8mm (standard power wire) 2- 12mm Post-Printing remove the support

http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wire_hole_offset = 20.0 hole_dia = 77 t_starts = 1 have_lower_frame = 0 tol = 0.7 wall = 1.2 hole_depth = 9 wire_dia = 8 lip = 3 t_pitch = 1.75...

http://www.thingiverse.com/apps/customizer/run?thing_id=1324924 Instructions Using the following options: wall = 1.2 have_lower_frame = 1 t_pitch = 1.75 hole_depth = 23 framewall = 4.0 t_starts = 6 lip = 5.0 wire_dia = 12.0 wire_hole_offset = 20.0...

... ... The original design kept popping out of the hole as the wires moved around, and also didn't quite seat the wires properly in relation to my printer, so I took the basic design and rebuilt it in OnShape. _Note: Designed for QIDI Tech 1 printer.

This was a modified version of someone else's upload because I found that I wanted somewhere for the wire to be hidden away.

Cardan 20mm With 16 Wire Holes

I wanted a box to put my electronic projects/ relays, d1 mini, esp8266 etc with wire out holes. so I remixed it using Tinkercad. ...Thanks to the Original Designer.

Updated matsekberg's wemos case to include a power socket and a wire hole for mounting to my WLED light strip project. Category: Electronics

Updated matsekberg's wemos case to include a power socket and a wire hole for mounting to my WLED light strip project.

Updated matsekberg's wemos case to include a power socket and a wire hole for mounting to my WLED light strip project.

This is a replacement part for my friends backpack but it could work with many other things. ...It has wire holes in the bottom and you should glue in the usb port

Customized version of https://www.thingiverse.com/thing:273159 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=273159