wire protector 3d models

While finishing our basement we realize after sheetrock was up and mudded, that we missed one of the electrical home runs and had to run a wire from one of the rooms to the mechanical room. Luckily we had an outlet for that line directly under one...

A thin but durable sleeve that spans the entire length of average 4.5mm wires such as headphones, earbuds, cell phone chargers, etc.

My aquatron power supply wire became broken by the continuous movement. ...With the help of my sixteen years old daughter, who designed the model with Fusion 360, we fixed the problem.

Earpods wire protector

printed in tpu, 10mm and 8mm wide wire protector for drones, best attached with either cable ties or double sided tape. ...50mm in length.

2 kind of wire protectors designed on Fusion 360. One to be used for a wire offset. A second one for a 90 degree wire turn. ...Printed with Materio3D PLA material.</p>

2fiddy Motor Wire Protector allows you to run the motor wires on the side of the arm to avoid prop strikes. ... ***Mirror the file for the other two arms*** More pictures here ...

2fiddy Motor Wire Protector allows you to run the motor wires on the side of the arm to avoid prop strikes. ... Mirror the file for the other two arms More pictures here...

This is a remix of this motor wire protector https://www.thingiverse.com/thing:4736322. I wasn't satisfied with the length of these for my TBS Source One and so i extended them to 35mm to look better and offer protection not only from prop strikes...

Xbee Air Motor Wire protector. ...It is wat it is.

Motor wire protector for the Iflight XL 10 V5. ...one version with room for LED Stripe and one version just for the cables

Made a motor wire protector for an apex rep that came with some horrible prints. Maybe it will fit the original as well? somebody let me know. This is my second revision and its just a tad (.2mm) thinner than the original, as well as a little shorter...

Protection for Motor Wires

This thing should prevent the propblades from chopping up your motor wires

A simple cover for the wires atop the arms of an Eachine Tyro99 kwad. Attach with two zipties. ...

Gatehunter RS5 by Dave C I create some Wire Protection for the Arms. ... Printing with Sainsmart TPU 100% infill

A thin but durable sleeve to cover the entire length of a 4.5mm wire such as headphones, earbuds, cellphone chargers, etc.

This will allow you to run the motor wires down the side of the arms to avoid prop strikes. Mirror the file for the other two arms. ...

A simple model to protect your wires from the propellers. ... Build video: https://www.youtube.com/watch?v=uYqXDLt4UJE Filament: PET-G

This will allow you to run the motor wires down the side of the arms to avoid prop strikes. ... Mirror the file for the other two arms.

A TPU pad I made for my Armattan Rooster that covers the motor wires on 22xx series motors. ... Dimensions: 50mm x 15mm x 6mm, 4mm opening on bottom for wires to run through, and 4mm wide cutouts on top for zip ties to sit in.

This model helps in protecting your wires from the sharp edges of the cutout in the frame. Features a tie-wrap arm. Uses 2 x M3 8mm with 2 M3 T-nuts to fix it to the frame. ... Part of my redesign of a more rugged skr 1.3/1.4 case for the ender

I don't use these to cover the entire esc but instead the last few millimeters - the intent is to protect the wires on the end of the esc from prop strikes. ...Printed in TPU and so far working great with XM20a's on my SCX-200 Picture is the 20mm...

I had a problem where the bowden tube and the wire harness would catch on the stepper motor. I designed this to add on top of the stepper cover. It has a pair of holes that would line up with the screws that hold the cover on, but I could not find...

TPU or Filaflex ESC wire protector print part & landing legs

Motor wire protector for the gatehunter rs5. ... Should fit on any frame with 9 mm wide arms.

Motor wire protector for the gatehunter rs5. Should fit on any frame with 9 mm wide arms. Category: R/C Vehicles

Very simple motor wire protector for the Novice 4. Use a 3.5mm ziptie to secure it to the arm. ...Print in TPU

This thing is quad copter motor wire protector. it will nicely protect wire from props. it has narrow(10mm) width and 60mm length for the vx210, chinese quad frame . ... but you can easily adjust it with your printer manager :)

This is just a simple motor wire protector / holder for the Armattan Marmotte frame. It wraps around the arm so there is no need for a zip-tie. ...It's designed to be printed in TPU.