wire spool stand 3d models
271798 3d models found related to wire spool stand.thingiverse
Wire spool stand designed to help me keep small spools of wire organized. I haven't tried but should scale reasonably for larger spools. If you scale it up and it is successful let me know. The holes in the guide are for 22 gauge (or smaller) wires.
thingiverse
A simple wire / solder spool stand I designed for my desk. Instructions Printed with a 20% infill. The result was a very sturdy stand that looks great on my desk. Printed out fine on my Printrbot...
thingiverse
I had 10 different wires, therefore i designed the the Cable_rail for 5 wires. ... With washers between the spools you can assemble up to 10 wires (see the picture).
thingiverse
Stand for soldering spool wire: For spool max wide 70 mm and diameter max. 90 mm. ...(bigger than that won't fit) Inner minimal diameter axle hole is 9mm (smaller than that wont fit).
thingiverse
Please increase shells to 4. ...I used Tree Supports which were easy to remove after printing. The Wire Spool will hold a little over 3/4 of the wire from the factory power wire.
thingiverse
Draadspoel (wire spool) 1+2 for 10 mm space Draadspoel (wire spool) 3+4 for 14 mm space After printing: use some glue to put the parts together.
thingiverse
i had some loose wire from ebay. ...so i made some spools to quickly print and organize that loose wire.
cults3d
Simple Wire Spool. ...Length 40 mm; Diameter 40 mm; Hole 10.5 mm; perfekt for coils :)
thingiverse
Wire Storage Spools, can be connected together as stack, scalable for the different diameters
thingiverse
This is the spool from the [Striveday™Flexible Silicone Wire"](http://amzn.to/2yExgDW) I used this model to help with my wire spool holder design. ... I have also included the AutoCAD 2018 DWG version.
thingiverse
A wire spool for your spare wires Dimensions: Inner diameter: 11.5mm Spool diameter: 20mm Wall diameter: 60mm Instructions Used 1.75mm filament, a layer thickness of 0.2
thingiverse
I designed this as I tend to buy wire off of a larger spool and do not like have great knots of wire hanging around. The wire I have on these is 22AWG. The Yellow spool has 50 metres of two strand wire around it, the blue has 20 metres of 4 strand...
thingiverse
Wire Spool outer diameter 100mm Inner diameter 50mm Hole diameter 21mm width 40mm Update Boss Modified. ...Update Compliance spool holder.http://www.thingiverse.com/thing:2139484 Update innner wirehole moveed.
pinshape
Simple wire spool. Length 20 mm; Diameter 40 mm. ...Depending of your printer's accuracy, little glue required or no glue required at all.
thingiverse
Simple Wire Spool. Length 40 mm; Diameter 40 mm; Hole 10.5 mm; perfekt for coils :) Instructions Print and screw the parts together. ...No Glue required!
thingiverse
Use it to convert a 46mm diameter cardboard tube in a wire spool. ... Work in progress: the snap fits have to be a little bit stronger
youmagine
Simple wire spool. Length 20 mm; Diameter 40 mm. ...Depending of your printer's accuracy, little glue required or no glue required at all.
thingiverse
... for wire. ...It has the same dimensions as the Conrad Electronics (German Shop) 25 m of 0.14 mm² insulated wire spools. I accidentally destroyed quite a lot of them when letting the drop on the floor. ... Glue both parts together with superglue gel.
prusaprinters
Simple Wire Spool. Length 40 mm; Diameter 40 mm; Hole 10.5 mm;<br/> perfekt for coils :)</p> <h3> Instructions</h3> <p>Print and screw the parts together. ...No Glue required!</p> Category: Other
thingiverse
This is a small wire spool. The inner diameter is 9 mm and the outer diameter is 53 mm. The spool consists of two parts, which have to be slotted and glued together. ...Print Settings Printer Brand: RepRap ...
thingiverse
Wire spool. One print with 3 parts. Press fit together with no glue required. Spool is 3" diameter and 1.75" tall. ...Print Settings Printer: Hictop Prusia i3 ...
thingiverse
the two sides of the spool snap together with force and are unlikely to come apart after assembly, so I would suggest threading the end of the wire on to the wire holder in the spool and through the hole in the cover before fully assembling, you can...
thingiverse
I had a few loose coils of wire tangling up the bottom of my electronics tool box. ...So here is a selection of spools to wind wire or string etc. on. ...Mix and match the sides to yield four different sizes.