wiring harness cover 3d models
198990 3d models found related to wiring harness cover.thingiverse
I needed a cover for the wiring harness to my trailer, since it sits out in the weather all the time. Without a cover the contacts get all corroded and difficult to use such that the lights on my trailer stop working. If this doesn't exactly fit...
thingiverse
(Remix of https://www.thingiverse.com/thing:4787938) I liked the Trailer Hitch Wiring Harness Cover, but wanted to attach it to the tow equipment, so I added this so that I don't lose the cover. This adds a littler arm and a loop to stick a zip-tie...
thingiverse
replaces stock cover. ...my stock cover blew away Print Settings Printer: anet a8 Rafts: No Supports: Yes Notes: printed the back face down. with a brim. and support. ...had a hard time to get the abs to stay down without a brim.
thingiverse
The wire harness covers for the back of the printer provide a much cleaner look and protect the wires from snags or damage. I have provided two upper models, one of which fits the stock Melamine t brackets for the frame and the other fits the...
thingiverse
Wiring Harness support for Eclipse injector wiring harness.
thingiverse
Wiring harness tab. ...Make sure to print in material suitable for use in intended conditions.
thingiverse
Want to avoid bloody fingers when pitting your 3D printers wires in the plastic sleeving? This is the tool for you. ...Print with only one wall.
prusaprinters
Want to avoid bloody fingers when pitting your 3D printers wires in the plastic sleeving? This is the tool for you. ...Print with only one wall.</p> Category: 3D Printing
thingiverse
The one I ordered from ebay didn't come with a wiring harness so I manually attached wires and created this cover to separate the wires so they don't come in contact with one another. It fits pretty well on its own but you can use a little epoxy or...
thingiverse
This little piece provides support for the print head wiring harness by clipping it to the filament guide tube and keeping it from flopping about. ...
thingiverse
Here is a nice tool to help easily remove the wiring harness from the case on an 8L90 transmission. ... I used 1.2mm walls and 2mm top and bottom in the settings on my print.
pinshape
I needed a clean way for the wiring harness (in tech flex sheath) to connect to the nema 17 stepper motor so as to not get in the way of other component swaps. I removed the stepper motors' body screws and replaced them with slightly longer M3...
thingiverse
These little brackets support the wiring for the print head using the bowden tubes as anchor points. ... I'm using them on a Qidi Tech-1 but they'll probably work with the Flashforge Creator or any of these other cloned printers.
thingiverse
Wiring loom support for hot bed. Made for Diggro Alpha-3, but should fit others of same design. Longer LK4 and LK4 Pro, Alfawise U30, etc. Inspired by a support I found/tried but did not fit my Diggro Alpha-3. Fits above the left rear bed...
grabcad
Creo wiring harness or cabling (battery connector)
thingiverse
Block off plate for the 1G dsm wiring harness coming from the passenger side of the engine bay
thingiverse
This thing is designed to repair a broken clip on a GM transmission wiring harness. ...The clip snaps over the back of the connector and securely latches onto the solenoid saving you from having to buy another harness.
thingiverse
This clamps the umbilical wiring harness going to the effector to the top plate from the bottom and top of the plate fixing in place and directing the harness between the X and Z columns out the way of anything it could snag. The clamp is designed...
thingiverse
The existing wiring harness can be used as it, but I found it necessary to use a slightly longer bowden tube than supplied with the Ender 5. It requires drilling and tapping a 4mm thread in the hot end carriage using printed base piece as a guide....
thingiverse
This is a wiring harness conduit clamp to replace the original smaller one that comes with the Ender 6 core xy 3d printer. The original is too small, so only the wires are able to fit through it. I made this one so that the conduit itself is clamped...
thingiverse
This is a Heated Bed Wiring Harness Support for the Winice M09 3D Printer / Zugentlastung fürs Heizbett für den Winice M09 3D Drucker It's a mod from the Part for the Longer LK4 Pro https://www.thingiverse.com/thing:4165104
thingiverse
My buddy needed a spacer to attach his 7 way trailer wiring harness to his pickup so I designed this for him. Hopefully, somebody else can find it useful as it is not commercially available according to my friend. The included stl is 20mm tall...
cults3d
This is a Heated Bed Wiring Harness Support for the Winice M09 3D Printer / Zugentlastung fürs Heizbett für den Winice M09 3D Drucker It's a mod from the Part for the Longer LK4 Pro https://www.thingiverse.com/thing:4165104
prusaprinters
This is a wiring harness conduit clamp to replace the original smaller one that comes with the Ender 6 core xy 3d printer. The original is too small, so only the wires are able to fit through it. I made this one so that the conduit itself is clamped...
prusaprinters
There is a slot to hold a 4mm-wide zip tie to secure the wiring loom. (Note: ziptie slot not yet tested.)</p> <p>The snap fit is reasonably tight and difficult to push in (to avoid inadvertently falling out while moving.) If it's not snapping in...
thingiverse
Parts list: 1x Bottom Piece 1x Gimbal + Face switches cover 2x Unions to connect gimbal cover to the elastic cords running down the sides 2x Shoulder covers *NOTE* I only have the "RightShoulder" STL file attached. I use DesignSpark and they don't...
thingiverse
Make sure to print in material suitable for use in intended environment.