wltoys 10428 3d models
1020 3d models found related to wltoys 10428.cults3d
Rear differential guard for wltoys 10428, this guard protects the differential from stones and strengthens the rear axle They are to be assembled with 10 M2x6 screws. ... the protection must be printed in TPU to adjust to the differential.
thingiverse
Mounted on WLToys 10428-B2 model. Durability not tested yet but maybe it will be better with PETG or ABS. Please refer to manual to access and disassemble differential. You need to replace gearing and diff axles by the printed part as the...
cults3d
... ...Mounted on WLToys 10428-B2 model. Durability not tested yet but maybe it will be better with PETG or ABS. Please refer to manual to access and disassemble differential. You need to replace gearing and diff axles by the printed part as the picture.
thingiverse
Those clips give the ability to set the spring preload on Wltoys 10428 (or others) models. I was disapointed that this setting wasn't possible on the 10428 whereas you have a nut on the smaller 12428 model to do the job. Also I found the 10428 to be...
cults3d
Holder for TS832 Transmitter to be mounted on Wltoys 10428 RC car
myminifactory
A basic dash with ham radio and gauges for my 10428-B cage. ...
thingiverse
A basic dash with ham radio and gauges for my 10428-B cage. ... update : changed width, was a bit too wide.
thingiverse
Sencillo soporte para camara FPV tipo RUNCAM en Wltoys 10428
thingiverse
moving the shock absorbers from the horizontal position to the vertical position. ...printed in horizontal position
thingiverse
a slight shift in battery weight from the rear of the model to the front with subsequent suspension modification.
thingiverse
Just a simple front suspension arms I made for my WLtoys 10428 ("K949" and also "Vaterra Twin Hammers"). I printed it in PLA and PETG, laying flat and standing on a side. Both materials are to brittle to withstand bashing around. sadly my...
thingiverse
A basic basket to fill the gap between the battery plate and the rear of the cage.
myminifactory
A basic basket to fill the gap between the battery plate and the rear of the cage. ...
thingiverse
Son dos archivos, uno la caja y otro la tapa que debe ser pegado con la gotita, lo realice de esta manera para ahorrar filamento. Esta es una nueva versión donde cambie la forma del anclaje ya que el anterior se rompía con facilidad. ...Para mayor...
thingiverse
Blinkers use the gear channel (three state switch on 10428 remote control radio). Classic servo channel assignment and bind procedure. "Motherboard PCB" can be ordered here: https://oshpark.com/shared_projects/HbG4uvoM Please note the PRO...
thingiverse
The Roof and Bonnet are remixes and the side panel is my own creation. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/jS6aEJOHuO7
thingiverse
I designed this steering upgrade from the ground up because I was tired of the horrible bump steer, even with upright shock towers the other bell crank setups I tried still suffered. This setup was designed to actually complement the stock front...
myminifactory
Sencillo soporte para el transmisor TS832, solo para este modelo de auto RC. El encastre en diagonal es muy delicado, colocarlo con cuidado. ...La tapa la tienen que pegar con la gotita o con cualquier pegamento.
cults3d
█║▌│█│║▌║││█║▌│║▌║ SongoLand 2017 YouTube █░░░█ █▀▀ █░░ █▀▀ █▀▀█ █▀▄▀█ █▀▀ █▄█▄█ █▀▀ █░░ █░░ █░░█ █░▀░█ █▀▀ ░▀░▀░ ▀▀▀ ▀▀▀ ▀▀▀ ▀▀▀▀ ▀░░░▀ ▀▀▀ Hola amigos, en el video de hoy, traigo como le he echo el kit de arrastre para remolques a mi wltoys 10428 B...
thingiverse
█║▌│█│║▌║││█║▌│║▌║ SongoLand 2017 YouTube █░░░█ █▀▀ █░░ █▀▀ █▀▀█ █▀▄▀█ █▀▀ █▄█▄█ █▀▀ █░░ █░░ █░░█ █░▀░█ █▀▀ ░▀░▀░ ▀▀▀ ▀▀▀ ▀▀▀ ▀▀▀▀ ▀░░░▀ ▀▀▀ Hola amigos, en el video de hoy, traigo como le he echo el kit de arrastre para remolques a mi wltoys 10428 B...
thingiverse
This is a new housing for the receiver with brackets for mounting. ...The BOM, SW and all data needed to build your receiver can be found here: https://www.thingiverse.com/thing:2862809 It allows use of standard 3-pin servos and binds to the original...
thingiverse
This is a wheel hex hub/nut which fits the WLtoys 10428 (K949).
thingiverse
This part is used to bring back your WLToys radio's wheel on centre when you release it. I used PLA+ for this part because I can't print ABS at this moment. (220°/60°) To reduce the fragility of the part, I designed the part with a thicken of...
thingiverse
... racing in order to reduce the body roll and energy absorption. (Not recommended for off-road) No support needed. can be printed out within 4 min per clip. This is a remix from Wltoys 10428 shock clip by ERICS89 February 01, 2021
thingiverse
This is a linkage to replace the stock shift linkage between the shift servo and the 2 speed transmission on the WLToys 10428 series of vehicles. My truck has been upgraded to use a full size shift servo, and using the stock shift linkage with the...
thingiverse
This is a bracket to hold the receiver for WLtoys 10428 crawler. ... You can find the receiver here: https://www.thingiverse.com/thing:2862809
thingiverse
Wltoys Tower shock protection protect the front shocks and the tower from scratch