wooden spool holder 3d models
382268 3d models found related to wooden spool holder.thingiverse
However it was difficult to change spools so I've printed this support designed for an equilateral triangle wooden spool holder. Instructions Simply print out and screw to the wooden frame. ... I printed with PLA at 210C with a .35 nozzle and .15...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=735213 Instructions Using the following options: arm_thickness = 2.4 inner_diameter_backlash = 1 number_of_arms = 6 arm_compression = 1 chamfer_depth = 3 quality = 60 height = 15 wall = 3...
thingiverse
#FilamentChallenge Instructions For holding a standard spool, cut four 14cm pieces of 1/2 inch (13mm) square wood dowel. It may be necessary to sand down all four sides of the last 15mm or so of each piece. A tight fit in each joint is desired. If a...
prusaprinters
It's Universial: The setup can be extended to accommodate multiple spools if a longer horizontal dowel is mounted between two assembled "stands". Alternatively, any size spool can be fitted so long as the wood dowels are cut to appropriate sizes. ...A...
thingiverse
Customized version of http://www.thingiverse.com/thing:605196 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=605196 Instructions Using the following options: EH = 5...
thingiverse
The small spool holder can be used with small spools that can not be fitted on the large spool holder. The pieces of the spool holder are glued together. All wholes of bearings can be different sizes. If the ones provided don't fit, new ones...
thingiverse
Spool holder horizontal for wooden board, useful to optimize the space used by the many open spools present in the laboratory. Developed to withstand the weight of a new spool 1kg. Suitable for generic spool RS 200 GH and Zortrax. Important: wooden...
thingiverse
This is simple spool holder for 50mm wooden beam. Quick solution of problem how to use 3kg spool of filament. You will need four 608 bearings, little bit super glue for connect cap and body together and eight wood screws for mount. ... As axis you...
thingiverse
A simple spool holder for your Prusa I3 made with wooden frame. ... Tutorial can be found here http://www.trustfm.net/hardware/3DPrinter.php?page=Extras1 The model was made using FreeCAD the sources are included
thingiverse
I could not find a spool holder for my cheap eBay printer that fitted the wooden 5mm thick frame. So a adopted one that I found on here. I adjusted the gap to fit and added a cut out for a notched 200mm long spool pole that would fit perfectly each...
thingiverse
Loved the design, but we don't have 15mm PVC here in the USA.
thingiverse
This is a template for a wooden spool Holder. It uses 5/8 dowels 128mm long and about 11.6mm thick plywood. ...The other accessories that you see in the photo are available on my thingiverse page.
thingiverse
Just knocked this up to enable me to use the old Geetech wooden spool holder with an 8mm screw rod to hold the spool.
prusaprinters
This is a template for a wooden spool Holder. It uses 5/8 dowels 128mm long and about 11.6mm thick plywood. ...The other accessories that you see in the photo are available on my thingiverse page.</p> <h3>Print instructions</h3><p>Category: 3D Printer...
thingiverse
Liked my wooden spool holder from my MakerFarm Prusa i3v so I printed on up to mount on the extrusion of my new MakerFarm 12" Basic Pegasus. ... Printed up two different sizes.
thingiverse
Hello, here is my wooden filament spool holder. It's designed of 6.36 mm Plywood. ...To assemble you need 4x M5x25 Screw 4x M5 nut 12x 5,3mm Washer 8x F695ZZ bearing Regards Toby
thingiverse
Instructions The spools are 160mm in diameter and 90mm in width. Each spool requires two ends and two plates cut out of 3mm MDF and glued together. The easiest way is to print out the PDFs, double-check the scaling is 1:1, glue onto the MDF and cut...
thingiverse
A wider base for the laser cut wooden Printrbot spool holder to accommodate wider filament spools. This particular width (89 mm) is to accommodate filament reels from reprapworld.com. Instructions The dimensions of this piece are made to exactly...
thingiverse
universal wooden spool stand. ...required 3D Parts from printer, 2 pcs bearing and 3 pcs 3 mm screws, nuts.
thingiverse
Appropriate lengths of threaded rod or hex bolt Spool carrier Update 12/15/2012: The bearing area is a bit snuggle to undersized, scraping and sanding will be in order. I'm working on an update that fixes this. The axle hole doesn't need to be the...
youmagine
... The aluminium plate is 6mm thick and the part is designed for a nice tight fit on that thickness. Other thicknesses are easy enough to make.I reused the shape from the wooden spool holder that I designed as it fit an 8mm threaded bar very nicely.