wopr 3d models
18 3d models found related to wopr.thingiverse
Front latch positions have been moved slightly Groove around small bolted hatch in front has been made thinner Mouse hole added to rear for routing wires Hole pattern on tall console (above where it says WOPR) has been modified to be more accurate...
thingiverse
Slightly more detail on my blog: http://netninja.com/2012/08/03/is-that-a-wopr-in-your-pocket/ Instructions Print and enjoy, but do not start any global thermonuclear wars. On a home 3D printer, you will absolutely have problems with the overhang,...
thingiverse
I was impressed with Corey's more accurate WOPR, but needed the back open to hold a 170 pin breadboard AND run wires from my "cube bell" to my desk. I also split the model for those, like myself, that have printrbot or other smaller printers. Marked...
thingiverse
WOPR - Greetings, Professor Falken - License Plate Frame https://www.youtube.com/watch?v=NHWjlCaIrQo
cults3d
WOPR - Greetings, Professor Falken - License Plate Frame https://www.youtube.com/watch?v=NHWjlCaIrQo
prusaprinters
WOPR - Greetings, Professor Falken - License Plate Frame Print Settings Printer Brand: Creality Printer: CR-10Rafts: Doesn't Matter Supports: NoResolution: 0.2mm Infill: 25 Category: Signs & Logos
thingiverse
UPDATE 10/03 or 03/10 depending on which side of the pond you are on. anyway, took several attempts to print and I learned that my measurements were a little off, please print at 105% to fit the 170 pin breadboard. Accessory pieces can be found here:...
thingiverse
WOPR - War Operation Plan Response, License Plate Frame https://www.youtube.com/watch?v=iRsycWRQrc8
cults3d
WOPR - War Operation Plan Response, License Plate Frame https://www.youtube.com/watch?v=iRsycWRQrc8
prusaprinters
WOPR - War Operation Plan Response, License Plate Frame Print Settings Printer Brand: Creality Printer: CR-10Rafts: Doesn't Matter Supports: NoResolution: 0.2mm Infill: 25 Category: Signs & Logos
thingiverse
This is just a modified version for an OLED Display for a Wifi print monitoring with Octoprint I did in Tinkercad using: https://www.thingiverse.com/thing:1120005 and https://www.thingiverse.com/thing:2884823 Props to the original modelers! ...
thingiverse
The large bit holds a 72mm by 47mm perfboard from 'da shack' The small box with cover is meant to hold a single button as seen in the group shot. The other part is for hanging on a cubical wall. Remix as need to fit your project. ...Designed to go with...
thingiverse
WOPR - Would you like to play a game, License Plate Frame https://www.youtube.com/watch?v=NHWjlCaIrQo
cults3d
WOPR - Would you like to play a game, License Plate Frame https://www.youtube.com/watch?v=NHWjlCaIrQo
prusaprinters
WOPR - Would you like to play a game, License Plate Frame Print Settings Printer Brand: Creality Printer: CR-10Rafts: Doesn't Matter Supports: NoResolution: 0.2mm Infill: 25 Category: Signs & Logos
pinshape
Video of LED's in action here: https://youtu.be/zWpbHMqR2c0 Instructions: Print (note I ended up scaling the WOPR to 105 %) , sand, paint -- I used acrylics. except for some parts that were metal on the original, then I used Testors...