wpl 6x6 3d models
2733 3d models found related to wpl 6x6.thingiverse
Measured up and modeled the parts needed to use a combined truck for the 6x6 WPL trucks. so the axles will work together better than if they are independently leaf sprung like some older models come with. I have not printed this myself, and cannot...
thingiverse
RC Rocketlauncher for Amewi / WPL 6x6 Trucks like the Ural 4320 Need: 2x 2mm Steelwire 2x 3mm screw and nut 2x 12mm servo 2x microswitch wire Rocket engine for example B4-4 print settings Launcher Infill: 20% Support: yes print settings Rocket...
thingiverse
Huge bed that I designed for the WPL series of trucks, I made it for a 6x6, its currently aWIP but I wanted to share what I have so far. ...Comments and suggestions are appreciated.
thingiverse
Rocketlauncher an Rockets for WPL / Amewi 6x6 Trucks like the Ural 4320 Needs to complete: (only compatible with own TX/RX) 2x 3mm screw and nuts 2x 12mm servo 2x microswitches 2x rocket engines B4-4 with electric igniter 2x 1,5 to 2mm steelwire...
thingiverse
Frame for 6x6 scale using WPL components. Use M4 bolts to connect the frame. The mount for the transmission is universal. ...Servos use MG90 or SG90
thingiverse
a kit to turn your wpl c14 or c24 into a 6x6 on stock 4link suspension! the only modification to your c14 would be cutting off the bed frome the tool box lock bump back! it preforms so good and im not running the updated axle if i had the new mid...
thingiverse
Rocketlauncher fpr WLP / Aemwi 6x6 Trucks Rocket print with 100% infill. Laucher with 10% infill. needed: 2x 3mm screw and nuts 2x12mm servo 2xmicroswitch Use B4-4 rocket engines. ...
thingiverse
... you want to make the trailer longer using multiple kits. The front pivot on the trailer uses a 3M screw to join them together and the king pin screws to the bottom of it Will make more WPL related trailer stuff in the near future for this 5th wheel
thingiverse
Shorter upper front link for the trailer Basket conversion kit to add 6x6 on a WPL B24. ... It's reduce the angle of the rear drive shaft.
cults3d
this model could be used to add a second rear axle for 4x4 wpl's to make them 6x6, actually used on my 6x6 Pegaso 1083
thingiverse
havent printed yet, was a quick reconstruction of the original design. ...I take no credit, nor responsibility.
thingiverse
this design extends both motors out 9mm suiting the steel axles better --------------------- I used the same motors as the original: ---------------------...
thingiverse
i designed it for my wpl c14 6x6 to haul my wpl e-1! it works great! easy to install just 2 screws to mount it to the chassis and then 5 for the hitch part! i used m3 screws but you can us what ever you have i bet it would still work! i did not...
thingiverse
Customized version of http://www.thingiverse.com/thing:50437 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=50437 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:2477998 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2477998
thingiverse
Customized version of https://www.thingiverse.com/thing:666162 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=666162
thingiverse
Customized version of https://www.thingiverse.com/thing:2740279 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2740279
thingiverse
Customized version of http://www.thingiverse.com/thing:43406 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=43406 Instructions Using the following options:...
cults3d
I made a model who looks very close to that real patria 6x6.bicause in internet is no Patria 6x6 blueprints . ...in finished pictures is 6cm small Patria 6x6
thingiverse
This is an M35 6X6 with 3D Printed Axles. ...gearbox and driveshaft from MrCrankyface https://www.thingiverse.com/MrCrankyface/about
thingiverse
Geoboard 6X6 Outside dimensions: 17x17mm This is a basic Geoboard 6x6 dedicated to geometry education for kids. Use rubber band to "draw" geometrical shapes. ... I shared the CAD file on Onshape so you can customize it: ...
sketchfab
Simple 6x6 tin shed created in sketchup online. Fairly close to factory standards (sizes, standards of beams, bolts etc). This shed design was quite common in the 80’s-90’s. ...I did it to give to the local council for shed approval, as there were no...