wyse vx0 3d models
51 3d models found related to wyse vx0.thingiverse
I picked up a few of these thin clients from eBay for cheap, but they didn't come with mounting hardware. The PC is passively cooled, and needs to have sufficient clearance underneath for convective airflow. ... ...
thingiverse
quick and dirty remix for Wyse terminal rack mount. ... to print full set: - ears - left (twice) - right (twice) - middle (twice) - tray (twice)
thingiverse
Dell Wyse 5060 stand Simple stand for thin client In fact this will fit any 185 x 40 mm rectangular device. ... Quick print No supports needed
thingiverse
a quick and dirty mounting bracket for the dell wyse thinclient(low power x86 pc) to be used instead of a raspberry pi for klipper. ...naturally I used the most powerful design program in the world...TINKERTCAD
prusaprinters
Dell Wyse 5060 stand Simple stand for thin client In fact this will fit any 185 x 40 mm rectangular device. Quick printNo supports needed
thingiverse
Since i use a DELL/Wyse Z90DE7 client as a small linux-server for nas and some other projects. I needed more hdd space. The Z90DE7 includes a pcie port that is removable. ...I dont need it so its removed -> more space for a HDD.
thingiverse
In Cura, you load a stand from _wyse-stand-XXX.stl_ and the infill model from _wyse-stand-infill.stl_. Turn off _Ensure Models are kept apart_ in settings. Select the _wyse-stand-infill_ model, and then use the _Per Model Settings_ and set that model...
thingiverse
Recently got a Dell Wyse 5070 to use for OpenWRT router at home. It needed a simple way to be wall mounted, that still allowed dismounting for adjustments or relocation. Issues that require careful consideration: Depth of vesa screw length...
prusaprinters
You can easily find dirt cheap Via C7 terminals from Wyse. They can work as a retro machine or perform other functions. More often than not you can buy them without power supply and any stand or feets.</p><p>I designed mine to be easy to print, just...
thingiverse
Made for the Wyse V90/S30 series of thin clients, that can be loaded with a small linux distro like Puppy or DSL.
thingiverse
Dell Wyse 5060 stand Remixed from a larger stand, I was impatient and wanted it to print quicker, just print 2 and you're good to go. Mounted with some double sided sticky tape. ...
thingiverse
Just a simple wall mount for the Dell Wyse 3040 client. ...Made to mount sideways, but if requested, may be able to make one with cutout's in the bottom
thingiverse
This is remixed from Printables, https://www.printables.com/model/386499 I wanted a side mounted bracket for my Wyse 3040 running Klipper and couldn't find anything that worked and loved this design so I just modified it and added the V-Rail...
thingiverse
A simple base to hold a Dell Wyse 5070 mini computer upright. It's important to have it on end because of the heatsink fin orientations and the lack of a fan. ... This stand is a snug fit, has a fairly low profile, and doesn't block any air holes.
thingiverse
Has been tested on a Wyse C90LE, but should also work with all similar form factor Wyse terminals (V90, CX0, etc..) with rails along the edge. Also has holes for mounting using screws instead of the Command Strips. Each bracket has two 3mm holes. All...
thingiverse
# Source The source is also available at [github](https://github.com/swthemathwiz/wyse-5070-ethernet-adapter). The adapter is built using Openscad. _wyse-ethernet.scad_ is the main file for the adapter. It customizes a blank using information...
thingiverse
I got myself a fairly powerful thin client, the Dell Wyse 5020, to use as a home webserver. It did come with a 'stand' to sit upright, but I wanted to fix this to the wall near my main switch. So I designed this bracket and it's a perfect fit. ...
prusaprinters
Wanted a way to mount my Dell Wyse computer to the wall with the hard drive, took a Vesa Mount and this hard drive holder and mashed them together.Used PETG to print just in case the heat would melt PLA. ... I didn't use any supports and it came...
thingiverse
Wyse camera mount for the Anycubic Kobra Plus. It should also work on the Kobra Max, and theoretically on the base Kobra (but it will be somewhat above the level of the build plate on that unit). I just acquired this unit, upgrading from a...
thingiverse
I picked up a Wyse think client to use as an alternative to a Raspberry Pi for running OctoPrint. Until I was sure I this device would meet my needs, I used only components I already had: a 4 GB SoDIMM to replace the 2 GB unit within, an external...
prusaprinters
I was looking for a possibility to operate my 3D printer power-saving via Octoprint, so that I can also create timelapses and so on.So the device also needs some power to not be overloaded by the image processing.Besides, current Raspberry Pi's are...
prusaprinters
I picked up a Wyse think client to use as an alternative to a Raspberry Pi for running OctoPrint. Until I was sure I this device would meet my needs, I used only components I already had: a 4 GB SoDIMM to replace the 2 GB unit within, an external...
cults3d
This mounting bracket is meant to neatly and securely affix the Dell Wyse 3040 Thin Client to the back of the monitor using the standard VESA mount screws.
thingiverse
This is a Support that I've made for my Dell Wyse Thin Client Mini Pc. Just print 2 sets of this, assemble them with M5x12 screws, washers and nuts and install in you monitor or in a wall. I've printed the two main pieces side ways using...
thingiverse
... (from 62* to 65*) NOTE The Dell Wyse 5070 has USB 2.0 and USB 3.0 inside, even though the connector suggests both ports are USB 3.0 standard (see photo). ... Due to the high temperature inside the thin client, I encourage you to print with PET-G.
thingiverse
... it fit in the enclosure by shortening the support bar. I also changed the cable clips to make them fit a usb cable, as I'm using the WYSE in Webcam mode with Octoprint and a Raspberry Pi Original Mount: https://www.thingiverse.com/thing:4228362