wyze cam v2 target 3d models

I bought Wyze Thermostats, but found that they were created for vertical mounting. This makes them not usable with older Honeywell horizontal thermostat mounting. While you could just create new holes and such, I decided to make my own to use the...

This is an airsoft deer target used for target practice. ... Dimentions of target: X = 91.02mm Y = 101.20mm Z = 5.00mm

This is an airsoft deer target used for target practice. ... Dimentions of target: X = 91.02mm Y = 101.20mm Z = 5.00mm

This is a case for an ESP-32 Cam with USB power adapter. ... It fits for the holder from codemonkey1973

4 versions: plain, Smiley, Target, Check I printed the Smiley, Target, and Check face up with support inside the large hollow underneath. I printed the plain one face down with support only for the radius on the two edges. I'm confident that the...

A target dummy with a few nicks and scrapes.

A cool drone target to hammer into your backyard.

Simple airgun target for rifle, interchangeable once destroyed.

Target air soft plus foot 80mm on 80mm

Toy story target shooting 8cm in diameter Designs on request!

Target realizzato in PLA utilissimo per ripristinare gli originali deteriorati. ...

Primary objective: Engage target for firing sequence deployment.

Launching projectiles at targets using four distinctly sized plates.

It is a nerf target that is 1 mm

Target System for In-Door Live-Fire Training Facilities.

a small adaptor to install a 10 x 10 cm target on a 14 x 14 cm conical target holder

Wall Mount for the WYZECAM V2 - Simplify Your Home Security Setup Are you tired of juggling cords and wires to get your home security camera up and running? Look no further! Our wall mount for the WYZECAM V2 is designed to make installation a breeze....

Securely attach your Wyze Cam to a wall using a sturdy side arm bracket, reinforced with two strong strips of double-sided adhesive tape.

... redesign was more practical instead of using M5 bolts and T-nuts which may not be readily available. ...Printed fasteners do not always have the same thread pitch. This design simply snaps into grooves on the side of the frame Printed on Ender 3 v2

German: Hi Leute, ich habe diese tolle Halterung für meine Raspberry Pi-Cam IR von Punix81 (https://www.thingiverse.com/thing:4581788) gefunden. Leider habe ich festgestellt, dass mir die Sicht auf das Bett nicht gefällt - wichtig für mich ist der...

German: Hi Leute, ich habe diese tolle Halterung für meine Raspberry Pi-Cam IR von Punix81 (https://www.thingiverse.com/thing:4581788) gefunden. Leider habe ich festgestellt, dass mir die Sicht auf das Bett nicht gefällt - wichtig für mich ist der...

Some small target designs for shooting at with Nerf / Airsoft / etc. ...3 designs: with solid plate; empty target area; and one with a small slot to hold a card target or similar. ... Category: Toy & Game Accessories

This is an airsoft deer target used for target practice. Dimentions of target: X = 91.02mm Y = 101.20mm Z = 5.00mm Category: Sport & Outdoors

Some small target designs for shooting at with Nerf / Airsoft / etc. ... 3 designs: with solid plate; empty target area; and one with a small slot to hold a card target or similar.

This spinning target board is great for a game of darts, nerf target practice, etc. ...Not suitable for live ammo though.

Needed some big nails for my archery target. ... Sinks well in to the foam back and keeps the paper target in order.

Fillable target made for plinking. Target has a hollow center with fill hole on top.  

Here is a simple articulated and adjustable heatbed mount for the Raspberry Pi cam V2. It was an iterative process to get all of the angles dialed in to give a good field of view across the print bed. I have attached a picture showing what the FoV...

To improve the strength of the slider, it's been split into halves. ...Also, the brackets meant to hold the Pi Cam ribbon on the bottom of the fixture have been removed to simplify printing.

I already had these X gantry attachments, so I remixed this Wyze v2 mount to work for Wyze v3, and attach to my existing mount. ... Included mount and attachment.