x one 3d models
796446 3d models found related to x one.thingiverse
If you remove the heavy metal cover from the print head carriage on the X-one, there is nothing to trigger the X limit switch. This is my version of a small "plate" that will trigger the X limit switch. ... Inspired by the following designs: ...
thingiverse
extruder cooling duct for the Qidi Tech X-One Print Settings Printer: Qidi Tech X-One Rafts: No Supports: Yes Resolution: 0.2 Infill: 20%
thingiverse
Spool spacer for the X-One. ...ID 31mm, OD 51mm, Width 97mm. V2 updated with single bevel for smoother printing. Print Settings Printer: Qidi Tech X-One Rafts: No Supports: No Resolution: .20 Infill: 10 Post-Printing Before After
thingiverse
I was tired of having glue sticks and other tools laying around so I decided to make a small holder that will fit on each side of the X-One that is capable of holding the tool kit that came with the X-One and glue sticks or rulers etc.
thingiverse
... uploaded a stand to hold the other side of the spool. Watch the spoolhlder in action. https://youtu.be/AHI5L36hXvc *** I cut a rubberband in half and on the right handle of the X-one, to hold the powercable for the extruder under control ***
thingiverse
... hold nicely to the case. Keeps some sound and heat inside. 2 Sheets cut 9/18 square for the sides 1 sheet cut to fit as desired for the front All panels fitted to the exterior of the printer for ease of removal. Print Settings Printer: QIDI X-One
thingiverse
Print Settings Printer: Qidi Tech X-One Rafts: No Supports: Yes Resolution: .20 Infill: 15 Notes: Supports from build plate only. I had no problems with bridging on the top section. I used 3 layers on walls for rigidity. I printed in PLA however ABS...
myminifactory
This is the body of the spool holder to attach to the back of the Qidi X-One. All you need is to add a metal bolt and a washer on each end. ... This is the first 3d model I've ever created, so it is very simple--especially since I am teaching myself.
prusaprinters
For safer stand i also uploaded a stand to hold the other side of the spool. Watch the spoolhlder in action. I cut a rubberband in half and on the right handle of the X-one, to hold the powercable for the extruder under control Print Settings...
cults3d
Just some covers for the X-One or any other metal sided printer. I made these from 3/32 Lexan and some magnets. All items purchased from home depot. I just used some CA glue to carefully attache the magnets to the Lexan and the hold nicely to the...
thingiverse
V2 - Centered filament tube guide, larger frame joints and cable tie bar Print Settings Printer: Qidi Tech X-One Rafts: No Supports: Yes Resolution: .20 Infill: 25 Notes: 4 top and bottom layers for rigidity. I printed with PLA which has been holding...
thingiverse
https://youtu.be/-yKqy0ufaQQ This is my take on a cable chain for the Qidi Tech X-One. The chain is open so you don't have to run the wires through it. There are two different links in the chain. One with an open top, and one with an open bottom.
cults3d
This Thing is a remix of Rolandooo's "Qidi X-One Side Holder" to hold a Meco USB vacuum for cleaning up the stray bits of filament that inevitably end up under the print bed on my Qidi Tech X-One.
thingiverse
... center but placed for case directly. ...So PTFE tube holding point move to center of filament spool width. Print Settings Printer: QIDI X-ONE Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 30% Post-Printing Joint all parts
thingiverse
This Thing is a remix of Rolandooo's "Qidi X-One Side Holder" to hold a Meco USB vacuum for cleaning up the stray bits of filament that inevitably end up under the print bed on my Qidi Tech X-One.
thingiverse
Lower side (fin) settle ring first and put in guide and upper side holding ring tight. ...Support density required 30% Print Settings Printer: QIDI X-ONE Rafts: Yes Supports: Yes Resolution: 0.2mm Infill: 100% Notes: Using PLA
thingiverse
My Qidi X-One sits on a shelf about waist high, making it very difficult to view and use the touch panel. ... I built this bracket to move the display to an easy-to-use 45-degree angle.
thingiverse
This things is a little design to let me mount a spare iPhone 4 to the bed of my Qidi Tech X-One print bed. ...Now I can easily record videos up close.
thingiverse
... top guide is flush under the bottom of the heated bed then secured with the nut. Print Settings Printer: Qidi Tech X-One Rafts: No Supports: No Resolution: .20 Infill: 10 Notes: Printed with PLA. Duplicate to six total in slicer. ...Post-Printing
thingiverse
... that better matched my printer type. See the slides for a better description. Search Tags: 3D Printer, QiDi, QIDI TECH, QIDI Technologies, X One, X-One, Makerbot, Clone, print bed, knob, level, bed, adjustment, leveling, thumbwheel, thumb wheel
thingiverse
Playstation Eye Camera Mount for the Qidi Tech X-One. The camera mounts to where the handles would normally be. There's a friction fit to the camera, but I also used some hot glue to hold it in place. ... PS Eye Camera ...
thingiverse
The Qidi X-One 2 has a thicker bed so had to make these a bit bigger from the original project. Small piece of masking/painters tape on the underside lip of the bed helps the clips to grip onto the smooth metal and not slide off so easily. Prints...
thingiverse
This is just a ROUGH model of the frame of the Qidi Tech X-one 3D printer. I used a tape measure to take most of the measurements, so use this at your own risk. ... I made this model so that I could design an enclosure around it.
prusaprinters
I built this bracket to move the display to an easy-to-use 45-degree angle. Print instructionsCategory: 3D Printer Parts Summary My Qidi X-One sits on a shelf about waist high, making it very difficult to view and use the touch panel. ...I built this...
thingiverse
The files attached are QIDI X-One PLA & ABS fff files. Beware these files are not perfect and should be verified with a test cube print. When printing a test cube watch the entire print layer by layer and note any issues you have. When making...
thingiverse
This mushroom replaces the overly large factory part on the Qidi X-One spool holder. I got tired of unscrewing the spool holder to change filament. Just unscrew the original from your metal spool holder, then screw this on! No more removing...
prusaprinters
I printed all brackets in PETG for strength and durability. Print instructionsCategory: 3D Printer Accessories Summary I used these parts to create an enclosure for my Qidi X-One. This allows me to print great with ABS. The brackets are glued to...
thingiverse
Washer , Spring Nuts, And Nuts Please adjust inside space For Side panel Please use 1step part from X-One rib.stl Using 4x M3 15mm screw at edge side. Washer , Spring Nuts, And Nuts Please adjust inside space For Top cover ...
thingiverse
The LED's in the Qidi Tech X-One printer are always ON when the printer is on. There is no way to turn them off. I don't need the LED's on while I am asleep, so I installed a toggle switch. I really wanted a rocker switch, but the hardware...
thingiverse
I broke one of the blades in the stock extruder fan on my Qidi Tech X-One. I replaced the 40x40x10mm fan with a 40x40x20mm fan. https://www.amazon.com/gp/product/B075SL6RYQ/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1 I used two M3x50mm flat...