x screw 3d models
536079 3d models found related to x screw.thingiverse
... with a strap slot. It screws to to the frame using the top plate screws, it can replace the top plate if you like. The screw slots will fit a washer for added support. ... Printed in TPU with 50% or more infill gives the base a solid feel.
cgtrader
m8 x 70 screw If you have any wishes or questions , feel free to ask. ...
prusaprinters
Wall Anchor #7 x ~30mm ScrewThe shaft of the anchor is designed for a ¼" drill bit.
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
cults3d
I've created an M4 nut and bolt that should work with adding lightweight things to your v-slots. I have not tested these, so use at your own risk. The nut that matches can be found here: https://www.thingiverse.com/thing:5581592 Thanks!
thingiverse
I've created an M4 nut and bolt that should work with adding lightweight things to your v-slots. I have not tested these, so use at your own risk. The nut that matches can be found here: https://www.thingiverse.com/thing:5581592 Thanks!
thingiverse
I had a problem when I change my X-Axis to be driven by a screw instead of belt. My screw was a bit shorter that I want and I don't want to spend more money in a 550mm long screw. This is because I have designed a support for the end of the screw.
thingiverse
The upper brace for the lead screw on my Anycubic Mono X was seemingly missing a bearing and the lead screw was not secured properly because of this. This is a simple design to remedy the problem. ... If printed out of filament you will definitely...
thingiverse
This is also another customizable screw hole but based on geeetech x-carriage design because the difference between vanilla or the rest of the design and geeetech; geeetech uss a 45mm lm8uu while most 3d printer uses 25mm lm8uu. Unless you want to...
thingiverse
If your belts are just hooked around screws, then these little cover thingies will take a lot of the strain off the screw. I noticed my screw was being pulled at an angle, so designed these to spread the strain out over three screws. You will...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
cgtrader
DIN Tank Dust Cap + Red Screw (empty tank) + Green Screw (full tank) Settings 3D printing: Top Solid Layers - 3 Bottom Solid Layers - 3 Outline/Perimeter Shells - 3 Infill Percentage - 30% Support - YES (From Build Platform Only)...
thingiverse
Remixed Arm Guard for 16mm x 19mm mounting holes motors
thingiverse
This is my first work for a 3d printer. ... Adapter for CR2 to CR23a. You'll need a 2.5x5mm screw for positive battery terminal. ...
thingiverse
-They are meant to be printed with the same printer (Photon Mono X or better), the margin of error is really small. ... -They create 4mm of distance from the metal tank frame to the floor, which prevents any dirt from sticking to the bottom of the...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
This is a simple E3D mount for the mini 3D printer from 3Dtje
thingiverse
Please Like and Follow me for design improvements. For access to the 3D Printing Knowledgebase with troubleshooting and design education, join our monthly Ko-fi membership. ...https://ko-fi.com/3dpkb/tiers
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Simple parts tray, thin 0.8mm walls to make it easy to print with a 0.4mm nozzle. Being so thin, not designed to be particularly durable or anything but will print relatively quickly for its size and not waste too much filament. ...For me it took...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647