x uav clouds 3d models
326917 3d models found related to x uav clouds.thingiverse
For X-UAV Clouds 1880 Wingspan Airspeed mount, is suitable for other aircraft Big Battery mount Motor mount fastening please do not judge strictly from the photo(Airspeed), the model is old and had hard falls The full latest version is at:...
grabcad
This is the X-UAV Clouds airframe with some parts I designed to convert it to VTOL. A Cobra Motor CP2814 400kV brushless motor has been modeled as well.There are a couple of imperfections, such as main wing height being off by ~1cm, the stabilizers...
thingiverse
This is a Cover for the small Tail Bay of the X-UAV Clouds. It is designed to hold specifically the Rush FPV Solo Tank VTX including the SMA Connector shipped with the VTX. But any other VTX with 20x20 hole spacing can be mounted too. Use some M2...
thingiverse
I made this pan and tilt to be as compact and sleek as possible to fit right inside the X-UAV Clouds nose with minimal cutting. I hope you like it. The pan is designed to have no bending load on the pan axis servo and allow 180° turning with a...
grabcad
The CAD model of the popular Mini Talon UAV sold by the Chinese company X-UAV
grabcad
Hi, these are some upgrades for the X-UAV Talon plane. ... Details and instructions can be found here: http://diydrones.com/profiles/blogs/x-uav-talon-upgrades
grabcad
This is the CAD model of the popular Mini Talon drone produced by the X-UAV company.
thingiverse
... one on front, one on back. flush with bottom and centered. thinking of maybe hinging it somehow. center tray I am using "X-UAV Talon flight controller deck" by epquilloy, published Dec 2, 2017 https://www.thingiverse.com/thing:2681515
thingiverse
This is a 3D printable X-UAV Mini-Talon. I have printed and assembled it. If you want to watch how I did that, head over to my youtube channel and watch the videos. Link below. This took me a lot of effort and time, please click the "like" and...
thingiverse
Not my design. ... I found this file on DIY Drones in a dxf format. I have made some changes with freecad removed holes and thicker. much learning for me to convert to stl format. http://diydrones.com/profiles/blogs/x-uav-talon-upgrades
thingiverse
X-UAV Clouds rear facing pop-up camera mount Parts used: Camera - Foxeer Falkor Micro Servo - Emax ES9251 Hinge Pin - 23mm section of round 3mm carbon rod Bolts - 2x 12mm M3 Servo control rod - 2mm steel rod with z-bends in each end. Length to suit.
thingiverse
X-UAV Talon Parachute Hatch V1 ========================= Introduction -------------- This is a simple servo-controlled parachute release mechanism for the X-UAV Talon. It requires one 9g-Servo and parts from the talon's (useless) side landing gear to...
thingiverse
This front skid plate is intended to be installed on X-UAV Talon 1.7m with no front wheel. This will protect front part of the fuselage on landings. The front skid plate has an impact absorbing segment that is meant to absorb pressure on hard...
thingiverse
Motor Mount for the X-UAV Talon (1.7m). This one fits the Cobra 3520 motor, with 50x50mm screw mounting (diagonal). Printed on ABS at 75-100%, 0.2mm layer height. Requires 4pcs M3 nuts and 4pcs 15mm M3 screws. Dec 1 2017 update: revised the motor...
thingiverse
As requested by Epquilloy, here's the Aeromapper-style wing lock for the X-UAV Talon. I only tested it with wing extensions, but you should be able to make it work without them as well. Glue some M3 standoffs into the wing and screw an M3...
thingiverse
[>>>] Generating Attributions log: [0] Thing Title : Smart Phone, iPod Touch or iPhone Smart Stand [0] Thing URL : http://www.thingiverse.com/thing:18914 [0] Thing Author : Area51 [0] Thing Licence : Creative Commons - Attribution - Non-Commercial...
thingiverse
It is scaled up 1.333 times (133%) and will still fit on a 200mm x 200mm print bed as long as it is printed diagonally. ...The print parameters I use are: * Brim - yes, 3mm * Support - yes, touching bed * Overhang angle - 70 degrees * Support...