x wing tokens 3d models

This is an update of [my previous set of tokens](https://www.thingiverse.com/thing:2420713) for X Wing. I wasn't really liking how the tokens looked or felt, so I went ahead and fixed that by rounding a lot of the parts. The new ones should look a...

to print the net of connor net, need to put 0 top and botton layer and 18% of grid infill. ... To rod bases need to use toothpick.

Star Wars X-Wing Token Holder

X wing token holder. ...not was made by me unknown designer

Tokens for X-Wing: The Miniatures Game. They are approximately the same size than the official tokens. Update 1: Added Reinforce and Tractor Beam tokens. ...Update 2: Added Condition, Reinforce Front, Reinforce Back and Illicit tokens

Intel tokens for Star Wars X-Wing mission Mission 18: Grab and Smash. Numbers 1, 2, and 4. ... Print one "1", two "2"'s and one "4".

Design to hold tokens for the X-Wing Miniatures Game. ...Implemented springs to keep tokens in place.

Modified token tray for X-Wing, should fit all the types of tokens (I think). Fits in a Harbor Frieght "Parts Storage Case". Uses 3mmx2mm magnets Borrowed some design/measurements from multiple other designs: ...

A tray for all the various tokens used in X-Wing. The center section can fit your damage deck, markers, and dice. There are holes so that magnets (.25 x .0625 inch) may be placed to secure the lid. The tray is designed to hold Curled Paw acrylic...

A tray for all the various tokens used in X-Wing. The center section can fit your damage deck, markers, and dice. There are holes so that magnets (.25 x .0625 inch) may be placed to secure the lid. The tray is designed to hold Curled Paw acrylic...

22/10/2018 - updated 2.0 tray with sleeve here https://www.thingiverse.com/thing:3170359 Tray for holding all those counters, second try has the following tokens 10 x critical hit 20 x shield 10 x ion 18 x stress 10 x evade 10 x focus 2 x cloak 2 x...

This is a remix from the token holder that GMBridge made. ...I credited that user in the remix section. I loved the token holder but wanted a lid. All i did was take the token holder and modify it so that there is a sliding lid. ...

... Placed on a small ship base (or fine, on their own) this caddy allows you to keep all the tokens for each ship, in plain sight, neatly organised and easy to place/remove from the ship.. ...So now you can carry that stack of tokens around with ease

X-Wing Token

... to keep it closed, I don't know, I will review it in a few weeks and see if it still holds on its own. Also if you want to modify it, here is the tinkercad link: https://www.tinkercad.com/things/av4Kdx0QSTI-modified-x-wing-token-tray-with-cover

x wing token tray 2.0 slides into enclosure so easy to transport, groove up middle so easy to open and rib at either end so reduced internal wobble. holds 10 critical tokens (also character icons) 20 charges (either) 15 id / target lock (3 sets) 15...

This is a very slightly modified version of user GMBridge's token holder design found here: http://www.thingiverse.com/thing:1329742 I just reconfigured the template holder slots to make them individual holes so the templates don't fall over when you...

This is a very slightly modified version of user GMBridge's token holder design found here:http://www.thingiverse.com/thing:1329742 I just reconfigured the template holder slots to make them individual holes so the templates don't fall over when you...

Tokens for X-Wing: The Miniatures Game, but include beers! ... You can change fillament at z = 2.2 to get different colours Designed by Beers And Ships Squadron https://www.facebook.com/BeersAndShips/

These are 76 ship ID tokens to replace the card board versions in a maneuver dial. They are up to date as of the release of Wave 7 of 2.0. These should work in any current maneuver dial. I haven't test printed them yet, but will be soon and I'll...

These are 76 ship ID tokens to replace the card board versions in a maneuver dial. They are up to date as of the release of Wave 7 of 2.0. These should work in any current maneuver dial. I haven't test printed them yet, but will be soon and I'll...

I've updated the Focus and Evade tokens to match the thinner borders used on these newer tokens and included them here. Trying to keep a bit of a clean, consistent look throughout all the tokens. If you have any suggestions for improvements to the...

This is a thinner version of ExcessRope's X-Wing Token holder which was in turn based on GMBridge's design. ...I decreased the height of the model so it would fit into the Stanley 25 Compartment Organizer that many people use to store their X-Wing ships...

This is a simple organizer I designed to keep my X-Wing tokens organized! I figured since we have a damage deck holder and template holder... why not make a token holder as well! Included are the STL files so you can out right print it, and the...

Here's the design, go nuts: https://www.tinkercad.com/things/d4OhcaxfouK-token-holder In case its not obvious, the spaces are for (top to bottom, left to right) Focus Tokens (F) Shield Tokens (S) Evade Tokens (E) Target Lock Red (TL) Target Lock Blue...

This thing was made with Tinkercad. ...A simple caddy for tokens to keep everything organized.

Stress Token from X-Wing Miniatures Game. Same basic size as the cardboard tokens. ... I filled the Stress Symbol with red crayon wax after printing.

Stress Token from X-Wing Miniatures Game. Same basic size as the cardboard tokens. ... I filled the Stress Symbol with red crayon wax after printing.

Simple harpoon token I printed since that ordnance is all the meta rage. ...Outer dimensions are the same as the stock cardboard token, the thickness is the same as some of the acrylic tokens I have (2.5 mm). ...Enjoy!

This is a dual color Ordnance lock token for the Xwing miniatures game.