x4r receiver 3d models
29021 3d models found related to x4r receiver.thingiverse
FrSky X4R receiver case w/button. Material to make top: SBS, Neylon (PA),Petg. ... Material to make case: any.
thingiverse
A 2 piece hard case for FrSky X4R receivers. Enables the use of double sided tape or velcro to fix to the model. Offers some protection in the event of a crash. The case weighs 6 grams in total. Printed in PLA at 0.2mm layer height. ... Use M3 x 6mm...
thingiverse
Enclosure for an FrSky X4R-SB Receiver Module with frame post mount holes
thingiverse
I had an incident caused by the antenna plug coming loose. This case prevents that happening. As it replaces the cardboard cover the final dimension as about the same. Because the case is thin, I recommend printing it at 0.1 layer height. ...
thingiverse
FrSky X4R / D4RII Receiver Stacking Tray, 30.5mm pitch holes to sit above Flight Controller.
thingiverse
FrSky X4R receiver case w/button (pinless version). Material to make top: SBS, Neylon (PA),Petg. ... Material to make case: any.
thingiverse
Simple holder for Frsky d4r or x4r style receivers intended to stack on top of a flight controller. ...The RX holder will need to be printed with supports, I suggest the Interface support in the newer cura 3.2.1
thingiverse
Mount for X4R FrSky receiver and antenna mount. ...Use 2.5mm cable ties and X4R receiver.
thingiverse
Enclosure for an FrSky X4R-SB Receiver Module with frame post mount holes and slipstream antenna direction
thingiverse
The receiver basically just snaps into place (I use that term loosely). No need for zip ties, tape, etc. The easiest thing to use for antenna wire supports is the 3mm coffee stirrer tubes that you can often get for free at convenience stores. The...
thingiverse
This print has a sister print for the vTx. These two prints are modular and fit nicely together. Both are printed in ABS. ... Make sure to check out other free stuff on my website www.typhonfpv.com
thingiverse
Built specifically for the Frsky X4R-SB (and similar) & Flight Controllers with 30.5mm hole spacing like the Naze32 or SP Racing F3 Flight Controller. Screw down with 2mm hex screws. Use coffee straws for antenna tubes to get a perfect 90 degree...
thingiverse
This mount incorporates lipo strap slots to hold the strap in place. ...I used double sided 3m tape to secure the receiver.
thingiverse
Not happy with the existing holders, I designed this myself to be used with X4R and D4R-II receivers. Its a tight fit so the cardboard cover must be removed. The label can be stuck on top for easy identification of the connectors. The antenna routing...
thingiverse
... be secure with or without glue/epoxy. The holes are slotted in the thin model to accommodate the different antenna PCB locations between the two receivers, but I will add the X4i receiver-specific model later. The D4R model is ready to go. ...Enjoy!
thingiverse
Simple and slim case for FrSky X4R (sb) receiver, cover is mounted with 2 small screws, holes for connectors and LEDs and information . ...
thingiverse
This is a mount for the FrSky X4R receiver. I designed it specifically for the ImmersionRC Vortex Pro but you can probably use it with other frames. It uses coffee stirrers for the antenna tubes. The antenna folds flat for transport and to keep it...
thingiverse
This is a super simple mounting plate for a FrSky X4R receiver for drones. I sized it to fit the common pattern with 30.5mm between each corner mounting hole. I use it on top of a stack consisting of Lumenier LUX v2 flight controller...
cults3d
Little Case for the FrSky X4R Singlebus Receiver for the Immersion RC. The notch is for the cable tie in order to prevent shifts. ... No Support needed.
thingiverse
Low Weight, low space 30.5mm support for Frsky X4R receiver. Easy access binding switch and LED, Two holes for antennas. Perfect fit and hold of the X4R, a little hard to fit the first time (easy with TPU) in case of difficulties crack-off the last...
thingiverse
Simple part to cover unused pins of X4R receiver when using S-Bus to help prevent shorting. ... Recommended printing in TPU Print Settings Printer: Prusa i3 ...
thingiverse
I actually got that one printed out, and my x4r-sb receiver didn't quite fit in there. The distance between the edge of the PCB that meets the antenna V-block and the antenna ports was too short, resulting in an insufficient bend radius on the wires....
pinshape
SummaryLittle Case for the FrSky X4R Singlebus Receiver for the Immersion RC. The notch is for the cable tie in order to prevent shifts. ...No Support needed.Print SettingsRafts: Doesn't MatterSupports: NoResolution: 200Infill: 10Notes: Mine is...
thingiverse
Little Case for the FrSky X4R Singlebus Receiver for the Immersion RC. The notch is for the cable tie in order to prevent shifts. No Support needed. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
This is a simple mount for the FrSky X4R-SB receiver fitting on a RCExplorer MiniTricopter Print Settings Printer Brand: RepRap Printer: BQ Prusa i3 Hephestos Rafts: Doesn't Matter Supports: No Resolution: 0.1 Infill: 50 Notes: Printed in PLA,...
thingiverse
Enclosure for a naked X4R-SB receiver made to accompany Receiver Antenna Protection Tube with outside diameter of ~3.10mm and inside diameter of ~1.5mm. The lid can be mounted by inserting two m3 nylon hex nuts in the back of the case and fasten...
thingiverse
Yet another Receiver holder that fits for Frsky D4R-II and X4R-Receivers snuggly. The actual antenna part can be tilted for easy transportation. The swivel-mechanism also helps in case of a crash. Fits both on my vortex 285 and vortex 250 pro. Most...