x525 frame 3d models
102875 3d models found related to x525 frame.prusaprinters
XT60 connector for X525 frame. With source file. Category: R/C Vehicles
thingiverse
Plug for the end of the arms on an x525 quadcopter frame with a slot that holds a LED. ...Also has the top removed to allow wires into the tube.
thingiverse
Improved upon my old design. Still havent had a chance to print yet. This one will hold APM, ESC, Battery and GPS. Not sure where to mount receiver or telemetry yet so im gonna improve after its printed. ... Edited 12 June: Now allows for 12.8mm bars...
thingiverse
Modified V2. For some reason all my STLs exported weirdly, so youre going to have to do some rotating if you want to print this thing. Not yet been tested. ... Started using solidworks instead of Sketchup and things work so much better.
thingiverse
Multirotor-quadcopter Centerplate with APM 2.5 holder with shock dumper mount for x525 frame
thingiverse
Parametric battery support for x525 quadcopter frame. To use with a velcro strap Openscad code is in spanish, sorry for the inconvenience. ...I'd traduce it if needed.
thingiverse
Replacement motor bracket for the X525 v3 quadcopter frame. After crashing my quad, I ripped a motor clean off. The original fiberglass motor bracket ripped completely into two. ...I designed and 3D printed replacements with a couple of hours.
thingiverse
Battery Holder for 1X 3000mAH Lipo Batteries Battery Dimensions must be within the following Guidelines. Height: 1.1" +/- 0.01" Length: 4.0" +/- 0.01" Width: 1.32" +/- 0.01" FOR 1 BATTERY AT A TIME. ... requires (M3x20) * 6 ...
thingiverse
These are little platforms to hold the speed controllers on the arms of a x525 frame.
grabcad
Exact replica of x525 frame motor mount. Stl file included for 3d printing. ...Z up cordinate system used.
thingiverse
Battery tray for HK X525 frame. Designed for 3300mah 45C 3S Turnigy LiPo battery but should fit any battery with similar dimensions. ... Prevents your battery from wiggling and slipping out of the velcro strap.
thingiverse
Modified original version created by Rego: https://www.thingiverse.com/thing:1640533 Decided to adapt it to my 13mm x525 frame. ... Did few modifications Enjoy!
thingiverse
Replacement spacer for X525 V3 frame. ... Instructions Print and secure with M3 screw and nuts.
thingiverse
Got an x525 frame from hobbyking, but no plate to mount my pixhawk, esc, bec, gps and receiver. ... I designed these very simple plates and gps mount to fit the frame.
thingiverse
I designed this adaptor to be able to fit a cheap gimbal suited for the DJI Phantom [https://www.banggood.com/FPV-2-Axis-Brushless-Gimbal-With-Controller-For-DJI-Phantom-GoPro-3-p-908068.html?rmmds=myorder&cur_warehouse=UK] to my X525 Frame. There...
thingiverse
It's for an X525 quadcopter frame. You can mount the MultiWii SE board directly to the bottom plate, the dampener is optional. This is my first Thing here, yaay. ...Print Settings Printer Brand: MakerBot ...
thingiverse
Tren de aterrizaje para quad X525 Print Settings Printer Brand: RepRap Printer: Hephestos Rafts: No Supports: Yes Resolution: 0.2 Infill: 100%
thingiverse
I needed a protective case for my KK2 flight controller to mount on my X525 Quadcopter frame. Instructions I printed in PLA at 40% infill for strength. I mounted my KK2 on nylon spacers and my...
thingiverse
A simple screw will hold the whole cam mount (use holes of X525 frame). ... There are some stand-offs (front) what need to be cut away & this version (v1) will too need some little rework to get it fit (depends on your positioning) but after that it...
thingiverse
Quadro Case for Hobby King X525 Frame Designed for: - CC3D Controller - Orange DSM2 8CH Receiver - LiPo checker with 4-Digit Display - BT Module (HC-05) - FPV Cam (Kingkong 800TVL) with 5.8GHz Transmitter The screw-holes in the MainPlate are designed...
myminifactory
Quadro Case for Hobby King X525 Frame Designed for: CC3D Controller Orange DSM2 8CH Receiver LiPo checker with 4-Digit Display BT Module (HC-05) FPV Cam (Kingkong 800TVL) with 5.8GHz Transmitter The screw-holes in the MainPlate are designed to fit M3...
thingiverse
X525 Simple landing gear. ...I used one screw of the motor support and for more restraint you can use other metric 3 screw
pinshape
... case for x525 . ... with case for lipo battery, battery level alarm and camera also tubeless version already . Allen screws metric 3, nuts are embedded with welder. The bolts is designed to fit in on the plates of fiberglass drone X525
thingiverse
... and camera also tubeless version already . Allen screws metric 3, nuts are embedded with welder. The bolts is designed to fit in on the plates of fiberglass drone X525 Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter How I Designed This
myminifactory
... case for x525 . ...with case for lipo battery, battery level alarm and camera also tubeless version already . Allen screws metric 3, nuts are embedded with welder. The bolts is designed to fit in on the plates of fiberglass drone X525 INSTRUCTIONS
youmagine
... The v2 version is stronger, mine (printed in ABS) survived a few hard landings without damage. Uses same pin as original. v2 also have indentations for the motor mount bolts as present on the X525. ... Pin fits in hole at the bottom of the foot.
thingiverse
Motormount for X525 Quadcopter, couldt find any printable files for it so I designed my own. This is a direct replacement for the fiberglass ones. Instructions Print and use, i suggest printing with...