x8r receiver 3d models
29016 3d models found related to x8r receiver.thingiverse
A simple hold down mount for a Frsky X8R receiver Print Settings Rafts: Doesn't Matter Supports: Yes
thingiverse
Made holder for my X8R to fit nicely in my rc plane, you can glue it where ever you want and the X8R receiver should fit there perfectly and lock it with rubber band. ... Used PLA with this model.
thingiverse
FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. ...Just print the parts...
cults3d
FrSky X8R Receiver & Antenna Mount - I made this originally to be used with the FireFly http://www.thingiverse.com/make:235170 printable drone. I couldn't find anything that suited my needs in mounting and protecting my receiver. ...Just print the parts...
thingiverse
Made this to hold receiver. ...Printed with no supports. Glued to Balsa airplane and receiver will snap in and out.
thingiverse
Receiver holder to fit in your R/C models. ... Antennas angle @ 90 Deg.
thingiverse
Holds the antenna of the [X8R Receiver](https://www.banggood.com/FrSky-X8R-2_4G-8CH-SBUS-Smart-Port-Telemetry-Receiver-p-79386.html?p=P818016937014201610N) at 90 degree angle for better signal quality.
thingiverse
Customised version of the upright X8R mount by https://www.thingiverse.com/thing:863785 Designed to fit the Tarot 680 Pro frame, It slots over the back canopy pin and can be held down with either tape, a rubber grommet or even 3M double sided tape.
thingiverse
Made for my printed ZMR250 style quad. No holes, drill your own. ...~45mm flat area between antenna supports Print Settings Printer Brand: LulzBot ...
thingiverse
II needed the holder of the antenna on my Slinger Wing for the FrSky L9R receiver. ...It is applicable also and to X8R.
thingiverse
A Holder for the Antenna witch can be secured by shrink tubing. ...Print Settings Printer Brand: Ultimaker Printer: ...
thingiverse
I am not sure is it compatible with X6R, and L9R. This version improve the other one I found in this site. Extend the upper and bottom plate. Easy to put double sided tape stick on plane. ... Added antenna click, no need addition parts to hold it.
thingiverse
This makes it easy to stuff in my backpack
thingiverse
mixed for own purposes base have diffrent distance between holes (6cm) mixed connection base-top
thingiverse
... cable ties (max 2.5mm) The 2 extra plates are just for better support hold. I recommend to use support on the two holding parts on top There are two files: X8R Final - Antennas pointing up X8R Reverse - Other version with Atennas pointing down
thingiverse
Recent x8r/x6r have been sent with no antenna pad covers so I created one after breaking couple of pads. ... Little insert is for locking the pad inside cover.
thingiverse
This is a modification of Carbo's orginal Antenna Holder which can be found here:http://www.thingiverse.com/thing:258146 I had the problem, that I can't fix the antenna joint on the frame, so I added a base to the design. In addition I needed to add...
thingiverse
I love the orignal design, but I need it to fold so I can put the plane in the travel case. I have a folding plane, and a non folding antenna holder just won't do! Technically this was draw from scratch, but I tried to be faithful to the orignal...
thingiverse
changes: 2015-05-15: added stronger version with 2 mm wall thickness (x8r_dual_v02_2mm.stl), use only if your printer has trouble with x8r_dual_v02.stl 2015-04-06: X8R versions also fits L9R (finally got one to check) 2014-03-17: added X6R version...
thingiverse
If you fly your Discovery with a Taranis X8R, here is a cover to, well, cover it up. This not only makes your quadcopter look more polished, but also prevents any of the servo wires from pulling out, which would suck. There are two notches in the...
thingiverse
I made FrSKY X8R receiver antena holder to screw detween botom plates for QAV250 frame
thingiverse
This is an antena mount for the l9r or the x8r receiver from frsky. ...It's designed to put the antennas at a 90º angle, wich is the recommended orientation.
thingiverse
I created a case for my X8R receiver since my receiver is the one with PCB antenna's. This is a tight fit on the PCB antenna covers if you have solder blobs connecting them as one of mine had, but you can still slide them into the PCB protectors...
thingiverse
Part in test. ...Need some edits to fit well. This is a part especially designed for ZMR250 with X8R receiver for gopro holder
thingiverse
I have made antenna holder for "FrSky X8R" receiver. This holder was used on "Tarot 680 PRO" drone frame's arms, which are 16 mm diameter. Antennas are fixed to the holder with plastic straps. The holder needs a little push to be fixed to the...
thingiverse
Mounting for a **FrSky X8R receiver** for your vehicle. Both antennas are mounted in a 90degree angle position. ... Please note: this mounting assume, that you **do not use** original plastic housing
thingiverse
This is a holder for the Antennas on the older Frsky X8R receiver. The X8R just fits under the canopy and this holder keeps the orientation correct and keeps them away from the props. Depending on shrinkage/expansion you may need to open up the holes...