xacto holder 3d models
328880 3d models found related to xacto holder.thingiverse
Designed to clip on to the vertical support wall of my desk and to clip my small xacto knife into.
thingiverse
This is a remix of "Wall mounted xacto holder" by jeremygold, http://www.thingiverse.com/thing:684621 Instead of as wall mount, I modified it so I can use it while crafting to safely store the knife. I mount the holder onto the side of my tool box a...
thingiverse
A Gridfinity based holder for the excellently designed [XACTO knife](https://www.thingiverse.com/thing:5665083) by [SolidDorks](https://www.thingiverse.com/SolidDorks). This allows up to 4 knives to be easily stored vertically. Gridfinity is...
thingiverse
Instructions Print the file - You'll probably need to use scaffolding to support the top section, but might want to check the sliced file to ensure you don't end up with a holder full of plastic! WARNING: Recommend removing the blade from your...
cults3d
Exactly as the title states, a holder for Xacto handle and blades. holds 5 standard blades and one small blade. ...I will probably add to that number at some point so stay tuned
thingiverse
The handle halves snap together but that is not enough to make the blade holder into a solid tool during use, so once the blade holder is assembled and tested, glue the handle halves together along the seam line with CA glue. The only part that...
prusaprinters
I took another pass at a revised blade cover for Unicorn Hatmaker's Xacto Blade holder, this one is intended to fit snugly, maybe even tightly, and doesn't take as much material to print. I dare say it's significantly more refined than my previous...
thingiverse
I was looking for a way to store my Knives and fond this design: X-Acto Knives Holder by jbchron https://www.thingiverse.com/thing:3094701 but I found I needed one with larger holes, so I designed one then designed one with smaller holes only more of...
thingiverse
A mount for the Ikea Skadis peg boards to hold a standard Xacto knife.
thingiverse
Customized version of http://www.thingiverse.com/thing:65816 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=65816 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:65816 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=65816 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:65816 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=65816 Instructions Using the following options: clipWidth...
thingiverse
Customized version of http://www.thingiverse.com/thing:201304 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=201304 Instructions Using the following options: lip = 2...
thingiverse
Customized version of http://www.thingiverse.com/thing:1268880 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1268880 Instructions Using the following options:...
thingiverse
This is a remake of https://www.thingiverse.com/thing:6132627 because @mister99 had a really good idea about making it threaded vs magnets. Now both are available. ...For this you will need the same M2 nut/screw as the above one but wont need any of...
thingiverse
X-Acto knife tool holder that screws to wooden back board. Instructions Orientate part on your build platform. ... Use low print resolution (save the plastic for more important stuff).
thingiverse
Ordered 100 blades for my xacto #11 knife, but it was in a small cardboard container. Created this to house the blades. Has a slot to help push out the blades (the protective oil they are covered in has a tendency to make them stick together).
thingiverse
... Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: 0,3 Infill: 10-20% Notes: Lay the holder on it´s back and stand the drawer upright for printing. ...Use 3-4 or more perimeters so the thing is a bit more solid.
grabcad
This Blade Holder was designed for an Xacto No.18 blade with a quick change feature. The holder is part of a semi-automatic tumor sliding machine for research lab application. The rendering was my first try at using PV360. ... I'll try Keyshot next to...
thingiverse
Tray to put your xacto knife or other tools in so it doesn't roll off the bench. I have not printed this out yet, so I can't say how well or which way to print is better, if you do print one, please post your print. ... Update 5/5/19 Added a second...
cults3d
I built this to hold my Mini Files and Xacto/Craft knives all in one place. The size can be manipulated in your slicing software. this model is an upgrade to my original model as with this model I made the Knife compartment higher and stabilised...
thingiverse
I have many different sizes/shapes of X-acto blades that have come with various sets I have bought. I got sick of having several different cases with blades, many of which could only hold one blade per spot because they used a ceramic magnet that...
thingiverse
Hold your screwdrivers, hex keys, and xacto knife so you always know where they are! I was constantly moving my tools and then searching to find them when a print started. Now they have a home! ...Print Settings Printer Brand: ...
thingiverse
I wanted a narrow, wall mounted option for my craft knives that filled a small gap in my work area. Print flat on back, no supports required. ... Hold in place with 2 No 8 screws.
thingiverse
on the clamp part is holders for a triangle scraper, edge scraper and extra blade. the tray slots onto to clamp and holds 2 pliers and an xacto case. tested, it does fit and work, but apparently thingiverse doesn't like my pictures, filesize is...
thingiverse
A nice and safe way to hold your xacto knife blades a glue stick and handle