xbox 360 case 3d models
259894 3d models found related to xbox 360 case.thingiverse
... Printed on Mendel Max 1.5+ using PLA. Printed at 0.2 Layer height. Print two so that you can insert into all case locks. I was surprised that it worked so well, heard "click" once fully inserted and clips inside xbox 360 were dis-engaged.
thingiverse
Case for the RF module from old xbox 360 to make a adapter for the wireless controller . ... Tutorial that i was using for the adapter : https://duino4projects.com/diy-xbox-wireless-controller-adapter-for-pc/
prusaprinters
Case for the RF module from old xbox 360 to make a adapter for the wireless controller . Tutorial that i was using for the adapter : https://duino4projects.com/diy-xbox-wireless-controller-adapter-for-pc/ Category: Video Games
cults3d
Game case keychain for Play Station and Xbox For games from the Ps2, Xbox, Xbox 360 and even DVD
thingiverse
This is a case for an Xbox 360 Slim Hard Disk Drive. I got a new Xbox 360 E 4GB Version and somewhere on the internet read about using my old xbox HDD, so I tried it and it worked fine, the only problem I found was it is loose on the tray. This...
thingiverse
For Xbox 360 Slim and Xbox 360 E. -all screw holes had 1 centimeter diameter counterbore, should support most generic PC HDD screws -holes for a pull tab, use scotch tape. ... -thick pry hole for when the pull tab was unusable/broken, use a flat...
thingiverse
Upgraded the Case designed by csin to include pins so that the hard drive can click into place, avoiding screws which could possibly stick out so much as to prevent the case from sliding into the slot properly. I also have a file for plugs for the...
thingiverse
This is a xbox 360 wireless controller battery case for 18650 lithium battery. After printing use two 1.5cm pieces of nickel strip as contacts between case and controller. Solder 2 wires to the battery and the other ends to the nickel strips. The...
thingiverse
Remixed from XBox 360 wireless controller AA battery holder bykingnaiis licensed under theCreative Commons - Attribution - Non-Commercial license. Design to fit with AAA Lithium Battery with USB charging chip. ...
cults3d
Remixed from XBox 360 wireless controller AA battery holder bykingnaiis licensed under theCreative Commons - Attribution - Non-Commercial license. ... Design to fit with AAA Lithium Battery with USB charging chip.
thingiverse
This is a remix of the 18650 case by [m0st1ted](https://www.thingiverse.com/m0st1ted). I redesigned it based on his/her design and rotated the TP4065 module in a way that charging during use is possible, when the plug of the type c cable is long...
thingiverse
xbox 360 wireless receiver wthi sync function on stm8blue
thingiverse
I removed the bottom details to reduce printing time. I also added a remove handle. There are two pins to hold hdd in place. If you want, you can also fix it with screws. I didn't change the direction. ...You will need to turn before slicing.
thingiverse
I was building an case for my Gen7 electronics from an old atx psu case that died ages ago, but was wanting to power it from an xbox 360 power supply, but couldnt find anything that I really liked, so I made this. The whole thing fits inside of the...
thingiverse
So I liked the box idea from Sargedawg and his logo on the top so took it a step further and made a custom molded insert so nothing should move around. I changed the dimensions of his box a bit to fit the insert and I am going to try printing the...
cgtrader
The 3D models was created on real base. It's created accurately, in real units of measurement, qualitatively and maximally close to the original. ... Model formats: *.max (3ds Max 2016 vray) *.max (3ds Max 2013 vray) *.fbx (Multi Format) *.obj (Multi...
thingiverse
... refresh the battery and they hold at least 90% of the charge again (1-2 weeks of use). You will need an old 360 controller (maybe this part can be printed too but I had a broken one) Video (in spanish): https://www.youtube.com/watch?v=OwgZ_S2whiA
prusaprinters
I have a couple of play&charge kits for my 360 controllers, but all the batteries don't hold any charge. Print instructionsUsing a more efficient charger like these designed for lipo/nicd/nimh you can refresh the battery and they hold at least...
thingiverse
Cleaned up and fixed some of the geometry. ...Derived from http://www.thingiverse.com/thing:5395
cgtrader
... you can refresh the battery and they hold at least 90% of the charge again (1-2 weeks of use). You will need an old 360 controller (maybe this part can be printed too but I had a broken one) Video (in spanish): youtube.com/watch?v=OwgZ_S2whiA
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58091 Instructions Using the following options: cable_diameter = 10 Font = write/orbitron.dxf label_orientation = 2 thickness = 1.2 label = XBOX 360
3docean
Realistic model of the Xbox 360 console. Great for high quality renders, close ups and animations. The polycount is manualy optimized so it’s not hardware intensive when importing to any program. There is no need for additional smoothing of the...
grabcad
this is the real deal Xbox 360with its cutting edge style and its awesomeness it's sure to wow the buyer of this magnificent piece of Microsoft Gaming