xbox 360 custom controller shells 3d models

... holder from Thingiverse, referenced as 2553522. ...This accessory is tailored for use in an Xbox Android streaming setup, where it plays a vital role in keeping the device securely in place and ensuring seamless operation during streaming sessions.

I designed a birthday gift for my friend, a huge Hulk fan and avid Xbox gamer. He's got great taste in gaming consoles, unlike me, who prefers playing on the PlayStation. I gathered all the necessary parts to create this unique present. ... Sources:...

... a remix of a great design adapted for a pegboard application. ... I added a little lug to keep the controller in place and a logo. Keep in mind that I have a custom battery witch is thicker than the original one, maybe you will have to redisign this.

I created this custom wall mount for my two reliable controllers using the design from Standby's excellent wall mount found on Thingiverse. However, one major issue arose: it included a headphone holder and a duck that didn't appeal to me. ...So, I...

The branches are designed to accommodate a controller with Strikeforce paddles added as well as an audio adapter - I haven't checked, but they likely would hold a standard controller just fine too. ...If you decide to create this project, note that...

... in place and it holds the hard drive in place very easily. The biggest issue with this print is the slits at the end to wrap something around so you can remove the drive from the xbox easily. ...If not you need to pry it out with a screwdriver.

Assembly: Acrylic glue or wood glue should be applied to the Xbox plate, then secured to the wall plate. Allow any physical glue like wood glue to dry for at least 24 hours before use. Use clamps. ...Twenty-five pound load-bearing drywall screws should...

Designed a simple stand for my Elite 2 controller. ... Enjoy!

The fix was just to place a washer in the screw and resolder the cables. Print instructionsThere is a dock for the special edition MW3 of the headset: http://gamingmodz.com/images/products/accessories/xbox/mw3-wireless-headset.jpg but it is a bundle...

Print instructionsThere is a dock for the special edition MW3 of the headset: http://gamingmodz.com/images/products/accessories/xbox/mw3-wireless-headset.jpg but it is a bundle and I dont need another headset for now. Instructions 1) Print (model...

Controller joystick extensions provide users with an extra level of precision and control over their gaming experience by offering additional analog stick functionality.

Make you gaming setup room different and more organized with personalized controllers stands.

A small stand for my controller. ...Its designed for the Play & Charge kit USB adapter

Controller stand for the Elite V2 that fits the charge base and looks great.

I have devided the controller mount to avoid any scratch on it

holds 2 controllers removed material from center of remix and added side supports to prevent flexing

The dual trigger is being reworked to enhance its rigidity. ...This adjustment necessitates some metal stripping from the controller housing itself.

From the Gizfreak's design I added a piece so i can hang it from underneath the desk. ... This piece can be altered on the fusion 360 file. ...

Remix on Gourdinos design. ...Added a hole so it could be screwed in, made it wider so the controller is more table, and rounded out the edges to seat the controller a little better

I've tested this on a 360 with the pack I made but the same should apply to a XBone controller.Parts list-3D printed parts6 x brass thumb tacks (4 if you reuse)2 x M3 washers1 x TP4056 battery charger with protection (eBay)1 x 1117-3.3 voltage...

I'm finally showcasing my very first design, crafted with precision in Fusion 360. I've carefully referenced the measurements from both the racing wheel and the Thrustmaster 458 RWI, but unfortunately, the printout hasn't materialized yet. ...If someone...

I designed this controller stand because I did not like the controller just sitting on top of the console. I wanted something to properly display the controller next the Series X. Hope you like it. ... This is a remix from...

customized with 3D Slash!

The same size, but extended to prevent the controller from tilting back and forth. ...I haven't printed it yet to confirm that the dimensions are accurate.

I didn't like that when I put by controller on the stand you have to intentionally line it up to make it centered. I made the stand wider so you can just set the controller down without having to set it down in center. Boom. ...Always centered and...

I didn't like that when I put by controller on the stand you have to intentionally line it up to make it centered. I made the stand wider so you can just set the controller down without having to set it down in center. Boom. ...Always centered and...

... mentioning that their holders tended to bow under load. ...To address this issue, I decided to reinforce my own holder with an additional support beam angled at 45 degrees, which effectively distributes the weight of the controller and prevents bowing.

This is a versatile desk holder designed specifically for controller clam grips, but it also works seamlessly with controllers that lack grip attachments.\r\n\r\nIf there's interest in an alternative design without the distinctive 'ears', eliminating...

Made this stand in PLA to hold my controller and make my setup look more organized.Printed the feet in TPU to gain friction so it won't slide around on the counter.

Modified this from https://www.thingiverse.com/thing:2923135 to fit two controllers in one. ... This project was created using Tinkercad, and can be easily edited online at https://www.tinkercad.com/things/kg2PeOjGIpZ.