xbox controller hanger 3d models

Quick (and dirty) remix of SmithRC's excellent Xbox 360/One controller hanger to add a flat top for "under mounting" so that it can be attached (via adhesive) to a shelf/desk bottom and act as a sort of "hanger" for my controller. ... Personally I...

Another hanger.. ...Yes, you can hide your controller beneath your desk.

xbox controller hanger for cubicle and spare AA battery slots. ... I did not need supports, your milage may vary.

Remixed from a previous headphone hanger, but instead created plastic threads and a plastic bolt so no other parts are required. Bolt.STL Can clamp on to desks 12mm or thicker Bolt Big.STL can clamp on to any thickness desk Bolt/threads were...

My cousin asked me to print this, and I had some trouble printing the first time with fewer supports (could be my new printer and/or leveling/print settings), so I doubled the thickness on the side legs and modified my support settings. Printed...

Modified version of adeochoa's "XBOX One Controller Wall mount" The one design now holds Xbox 360 and Xbox One controllers. Also removes a large amount of the volume of the print. ... Does require supports.

Modified version of adeochoa's "XBOX One Controller Wall mount" The one design now holds Xbox 360 and Xbox One controllers. Also removes a large amount of the volume of the print. Does require supports. ...Print Settings Printer: ...

Just another Xbox controller hanger/mount, but this time it's able to hang from under the table. I used double-sided tape to attach it to my table but there's plenty of space in case you want to use screws, but in that case, I would recommend adding...

Designed up because a buddy wanted me to print him up something to hold his xbox controller. Is designed to cradle the controller with something sticky such as a 3m adhesive pad holding it to a wall or side of shelf. ...Took a few iterations to get it...

I had already made the base design for the Xbox 360 controller hanger so I figured I would also include a design for wire racks. There are a few different wire rack designs, this one is designed to fit one with the large outside support being 7mm...

Inspired by: https://www.thingiverse.com/thing:1776565/makes Shorter, more durable, double screw hole

My take on the no-support version. ...45 degree walls plus 15mm bridging allow easy printing

No supports needed. Print it standing up. ...

it needs two screws

I designed this for a class project. ...I have no idea if it is even functional.

Apenas foi acrescentado o logo do xbox ao modelo.

Apenas foi acrescentado o logo do xbox ao modelo.

I was using a controller stand I originally downloaded from thingiverse, but the controller just takes up too much desk space. ... This low profile hanger allowed me to hang it on the apron running beneath the tabletop - out of the way but easily...

I wanted to hang my Xbox one controllers on the UPPSPEL pegboard, but the accessory kit you can buy at Ikea only comes with one hanger, so I have made my own. The V1 is simpler to print but is way less rigid, this is why I added the supports at...

Using the xbox-controller just to connect my headset, as my Logitech G920 Wheel doesn't have a headset-connector. So, I remixed the thing to hang the controller over the belt on the backside of the Playseat Challenge. Added two hooks for a...

I found quite nice and simple Xbox 360 Controller hanger for wire rackshttp://www.thingiverse.com/thing:1607027 and i just cut wire part,when i connect it to each other,Hope it will works) How I Designed This I just cut headphones hanger part from...

No supports, less weak parts, replaceable arms if damaged. I made this remix because the originals I printed broke off one of the arms with smaller kids. This model uses set threads (M3 x 4 x 5mm) and M3 tapered (countersunk) heads for a clean...

Designed this controller hanger for the ikea skadis pegboard. ...Nice, tight fit.

I remixed thing:1176663 for a sleeker design. ...I added two small pieces of double sided tape to keep the controller from sliding back and forth. ...I also reoriented it to print on it's side for optimization.

I remixed thing:1176663 for a sleeker design. ...I added two small pieces of double sided tape to keep the controller from sliding back and forth. ...I also reoriented it to print on it's side for optimization.

Remix of Xbox One Controller Wall or Furniture Mount by hegmar sits perfectly on xbox one x great to get controller of the desk and it just looks cool printed at .2 infill %15 no supports needed WARNING : Make sure you have the stand on the xbox so...

remix of https://www.thingiverse.com/thing:2808418, this is for the Xbox Series S to hang Controller off the side.

An easy way to hang your Xbox One controller and headset on your wall. The gap in the controller cradle is not wide enough to accommodate a chat adapter -- I'll be working on another version. ... http://unmaintained.com

Found the base of the design on Thingiverse ( https://www.thingiverse.com/Raizo12345 ) and then made it wider to utilize 2 pins and to support the controller better, put the pins in a better position so the holder sits flush, and secure. ...This was my...

Just taken the hanger from: https://www.thingiverse.com/thing:5185524 and reduced the overhang after the pins to improve airflow. ...Full credit to Ballistik1