xbox controller print 3d models

holds 2 controllers removed material from center of remix and added side supports to prevent flexing

Controller stand for the Elite V2 that fits the charge base and looks great.

Make you gaming setup room different and more organized with personalized controllers stands.

A small stand for my controller. ...Its designed for the Play & Charge kit USB adapter

I have devided the controller mount to avoid any scratch on it

Simple, and secure wall mount. ...The controller sits close to the wall

While testing the original file on my nephew's controller, I printed a small test piece to see if the buttons felt right. Results show it fits perfectly with no issues. Supports: For tree supports, use Cura's experimental feature. Make sure you...

Print Settings Rafts: No Supports: No Resolution: 0.2 mm Infill: 5% Notes: You might get away with printing your first layer a bit too thick. ...This would create a lip, making it stick nicely to your controller without needing any tacky tape at all -...

Initially, I relied on a fine-tip pencil to create an outline sketch of the controller back from memory, capturing its nuances in meticulous detail. ...Utilizing vernier calipers, I carefully measured critical dimensions and employed a protractor along...

Then while i was fitting the original file to my nephews controller i tested the little test print out to see if the buttons feel nicely and results are that it fits with no problem. Supports: For the supports I use the experimental feature in Cura...

Remix on Gourdinos design. ...Added a hole so it could be screwed in, made it wider so the controller is more table, and rounded out the edges to seat the controller a little better

Add Logo Dual Controller Stand https://www.thingiverse.com/thing:5150866/files https://www.thingiverse.com/thing:4755732/files

I designed this controller stand because I did not like the controller just sitting on top of the console. I wanted something to properly display the controller next the Series X. Hope you like it. ... This is a remix from...

Each grip is then able to easily screw into the nut as per the user's needs.They are designed with a textured outer layer to increase grip for the user. Included are 2 styles of grip:The long grip extends the joystick upward allowing for a more...

This is a basic remix, just doubled it, added logos and added a piece of material between the two controller stands

... mentioning that their holders tended to bow under load. ...To address this issue, I decided to reinforce my own holder with an additional support beam angled at 45 degrees, which effectively distributes the weight of the controller and prevents bowing.

I didn't like that when I put by controller on the stand you have to intentionally line it up to make it centered. I made the stand wider so you can just set the controller down without having to set it down in center. Boom. ...Always centered and...

I didn't like that when I put by controller on the stand you have to intentionally line it up to make it centered. I made the stand wider so you can just set the controller down without having to set it down in center. Boom. ...Always centered and...

I've tested this on a 360 with the pack I made but the same should apply to a XBone controller.Parts list-3D printed parts6 x brass thumb tacks (4 if you reuse)2 x M3 washers1 x TP4056 battery charger with protection (eBay)1 x 1117-3.3 voltage...

Modified this from https://www.thingiverse.com/thing:2923135 to fit two controllers in one. ... This project was created using Tinkercad, and can be easily edited online at https://www.tinkercad.com/things/kg2PeOjGIpZ.

My first test on editing 3D models. ... - Nintendo Switch Controller Stand Goku: https://www.thingiverse.com/thing:3996712 Don't forget to follow me for all updates and new model releases!

Final parts slide into place as I carefully snap the controller together. The clips secure tightly into the back plate, and everything fits snugly as it should. ...Sorry for the delay - a glitchy scanner slowed me down.

─ Modeling with c4d ─ ─ Control with 3d builder ─ ▼▼▼ MORE OBJECTS ▼▼▼ ►► https://cults3d.com/en/users/yiixpe/creations ◄◄ ►► https://www.thingiverse.com/yiixpe/designs ◄◄ ☺☺ Thanks for the coffee ☺☺ https://paypal.me/yiixpe

No need to search for the controller and clutter up desks, sofas, beds ...etc... ... Practical and useful, to try it is to adopt it and not to do without it anymore 😁

Would like to have an easy Holder for my Controller and Headset and so i made this. ...There are 2 holes for Screws but it's fixed with the upper alone also.

I needed a stand for both controllers and headphone in a single accessory. And here we are. If you like it, please leave a like. ... If you'd like to support me, offer me a coffee here: paypal.me/corons30

The branches are designed to accommodate a controller with Strikeforce paddles added as well as an audio adapter - I haven't checked, but they likely would hold a standard controller just fine too. ...If you decide to create this project, note that...

I couldn't find a controller holder for my series x and made this. No screws or fasteners needed. It just has bosses that fit in the holes on the top of the Series X. The short holder also can cover the power button because you cannot turn off the...

Found the base of the design on Thingiverse ( https://www.thingiverse.com/Raizo12345 ) and then made it wider to utilize 2 pins and to support the controller better, put the pins in a better position so the holder sits flush, and secure. ...This was my...

I made this modification to make the thumbstick fit more firmly on the controller. Ideal for Aerial Simulation games or even FPS ... Or for those who simply want to be more precise with their movements. ... The joint must be fixed with some...