xbox controller with paddle 3d models

A small stand for my controller. ...Its designed for the Play & Charge kit USB adapter

Remix on Gourdinos design. ...Added a hole so it could be screwed in, made it wider so the controller is more table, and rounded out the edges to seat the controller a little better

I remixed matt_longieliere's original controller stand using Fusion 360 to fit 4 controllers and it's working great!Printed at 0.16mm layer height on my BambuLab P1P usingPolyTerra Matte Cotton White PLAPolyTerra Matte Charcoal Black PLABambu...

Add Logo Dual Controller Stand https://www.thingiverse.com/thing:5150866/files https://www.thingiverse.com/thing:4755732/files

I designed this controller stand because I did not like the controller just sitting on top of the console. I wanted something to properly display the controller next the Series X. Hope you like it. ... This is a remix from...

While testing the original file on my nephew's controller, I printed a small test piece to see if the buttons felt right. Results show it fits perfectly with no issues. Supports: For tree supports, use Cura's experimental feature. Make sure you...

Print Settings Rafts: No Supports: No Resolution: 0.2 mm Infill: 5% Notes: You might get away with printing your first layer a bit too thick. ...This would create a lip, making it stick nicely to your controller without needing any tacky tape at all -...

... from memory, capturing its nuances in meticulous detail. Utilizing vernier calipers, I carefully measured critical dimensions and employed a protractor along with a compass to ensure accurate calculation of angles and curves for my replica design.

Then while i was fitting the original file to my nephews controller i tested the little test print out to see if the buttons feel nicely and results are that it fits with no problem. Supports: For the supports I use the experimental feature in Cura...

This is a basic remix, just doubled it, added logos and added a piece of material between the two controller stands

The same size, but extended to prevent the controller from tilting back and forth. ...I haven't printed it yet to confirm that the dimensions are accurate.

I didn't like that when I put by controller on the stand you have to intentionally line it up to make it centered. I made the stand wider so you can just set the controller down without having to set it down in center. Boom. ...Always centered and...

I didn't like that when I put by controller on the stand you have to intentionally line it up to make it centered. I made the stand wider so you can just set the controller down without having to set it down in center. Boom. ...Always centered and...

Two paddles are placed inside a sculpture of an old canoe.

I've tested this on a 360 with the pack I made but the same should apply to a XBone controller.Parts list-3D printed parts6 x brass thumb tacks (4 if you reuse)2 x M3 washers1 x TP4056 battery charger with protection (eBay)1 x 1117-3.3 voltage...

Each grip is then able to easily screw into the nut as per the user's needs.They are designed with a textured outer layer to increase grip for the user. Included are 2 styles of grip:The long grip extends the joystick upward allowing for a more...

Final parts slide into place as I carefully snap the controller together. The clips secure tightly into the back plate, and everything fits snugly as it should. ...Sorry for the delay - a glitchy scanner slowed me down.

Modified this from https://www.thingiverse.com/thing:2923135 to fit two controllers in one. ... This project was created using Tinkercad, and can be easily edited online at https://www.tinkercad.com/things/kg2PeOjGIpZ.

No need to search for the controller and clutter up desks, sofas, beds ...etc... ... Practical and useful, to try it is to adopt it and not to do without it anymore 😁

Made this stand in PLA to hold my controller and make my setup look more organized.Printed the feet in TPU to gain friction so it won't slide around on the counter.

I couldn't find a Series S controller mount, so I remixed the One S mount. Printing on side, so no support needed. ...I found printing the first layers slowly (around 40% speed) for the base helped adhesion a lot.

My first test on editing 3D models. ... - Nintendo Switch Controller Stand Goku: https://www.thingiverse.com/thing:3996712 Don't forget to follow me for all updates and new model releases!

I needed a stand for both controllers and headphone in a single accessory. And here we are. If you like it, please leave a like. ... If you'd like to support me, offer me a coffee here: paypal.me/corons30

... of a great design adapted for a pegboard application. ... I added a little lug to keep the controller in place and a logo. ... Keep in mind that I have a custom battery witch is thicker than the original one, maybe you will have to redisign this.

Found the base of the design on Thingiverse ( https://www.thingiverse.com/Raizo12345 ) and then made it wider to utilize 2 pins and to support the controller better, put the pins in a better position so the holder sits flush, and secure. ...This was my...

I needed a stand for both my wireless headset and controller, so I merged two designs into one seamless creation. When printing the flat connector, be sure to set at least 50% infill or risk snapping it during sanding if you plan to paint it...

I created this custom wall mount for my two reliable controllers using the design from Standby's excellent wall mount found on Thingiverse. However, one major issue arose: it included a headphone holder and a duck that didn't appeal to me. ...So, I...

... really ruff cause I used a Wood-PLA-Mix Filament! ... I made a Stand for the Receiver of my XBOX360 Controller. I designed it to make the range bigger while streaming gameplay from my PC to my TV. Very easy print. ...Just print it straigt as it is.

I couldn't find a controller holder for my series x and made this. No screws or fasteners needed. It just has bosses that fit in the holes on the top of the Series X. The short holder also can cover the power button because you cannot turn off the...

Used basic photogrametry to get a bit more accurate shape of the controller in order to make a snug fit for the holder. ... Just print it in whatever color you want using 0,28mm layer height, use 3,5mm screws for the wall mount, slide the holder in...