xl 650 3d models
7980 3d models found related to xl 650.thingiverse
Dillon XL 650 Toolhead Stand Print at 75% scale for Dillon 550 as per Wildcard97: https://www.thingiverse.com/make:343635 Apparently it sometimes prints the blank areas in a couple quadrants, might want to do a manifold check in something like...
prusaprinters
Dillon XL 650 Toolhead Stand Print at 75% scale for Dillon 550 as per Wildcard97: https://www.thingiverse.com/make:343635 Apparently it sometimes prints the blank areas in a couple quadrants, might want to do a manifold check in something like...
thingiverse
This is a 5.56/.223 arm bushing for the Dillon xl 650/750. ...Freecad file included.
prusaprinters
2018:Split the model into two, one for the old Dillon model with steel shell plate (photos) and one for the newer model with boss and cast shell plate.Look for “New” and “Old” in filename.Model shown in Super Blue Devil Design PET for the old Dillon...
thingiverse
Replacing the steel Index Cam on the XL-650 with this Index Bearing Cam, you get a reduced wear, lower friction and a smoother reloading. It is much easier to *feel* whats going on, when reloading. To assemble, you will need: - 1x 626zz bearing...
thingiverse
This is a wall mount for the Dillon 650 XL Casefeed parts. It will hold both the Medal threaded parts and the colored plastic inserts. No supports needed. ...
grabcad
3d Printable toolhead holder. Edit: Discovered that the wall thickness was way less than I intended on the original model. Fixed wall thickness and added a couple of chamfers. Some aftermarket Billet-machined toolholders are machined to a thicker...
thingiverse
This is a remix of a solid bracket for Dillon XL 650/750 bullet tray. I have cut the bracket so it looks nicer, is faster to print and doesn't require as much material. It doesn't require any kind of stand. If you don't have original metal bullet...
thingiverse
A .45 ACP case feed adapter for a Dillon xl 650/750. ...Probably works for other similar sized cases.
thingiverse
This is a 5.56/.223 case feed adapter for the Dillon xl 650/750. ...The freecad file is included.
thingiverse
This is a wall mount for the Dillon 650 XL Shell Plate Holder. ... No supports needed.
thingiverse
his is a wall mount for the Dillon 650 XL Casefeed Adapter Holder. Holes are keyed to allow parts to be lined up. ... No supports needed.
thingiverse
This is a wall mount for the Dillon 650 XL Station One Blocks. ...Slots are a little tight to hold parts tight so they do not fall out No supports needed.
thingiverse
Simple and double stand for Dillon XL 650 Toolhead. ... Simple toolhead stand is 100mm x 120mm x 30mm Double toolhead stand is 200mm x 120mm x 30mm
thingiverse
A 9mm case feed adapter for a Dillon xl 650/750. ...Probably works for other similar sized cases, I only tested it with 9mm Luger.
thingiverse
44 magnum case insert slide for a dillon xl 650/750. Print it 180 degrees on the x-axis w/ supports from print bed enabled. ...May need to smooth out where the rim is held in after print to get smooth operation.
thingiverse
This is a largesized case feeder body for the Dillon xl 650/750. Works for larger rimmed cartridges, tested with 44 magnum and 303 brit. Push the print in and give it a quarter turn to have the threads grip the coned end. ...Use supports on the non-cone...
thingiverse
This is a medium sized case feeder body for the Dillon xl 650/750. Works for ~30 caliber. Push the print in and give it a quarter turn to have the threads grip the coned end. ...Use supports on the non-cone end when printing.
thingiverse
A 30-06/308 case feed adapter for a Dillon xl 650/750. ...Probably works for other similar sized cases, I only tested it with these 2, works best for 308 if you put a piece of tape over the top ~.5 inch of the cutout.
thingiverse
308/30-06 case insert slide for a dillon xl 650/750. Print it 180 degrees on the x-axis w/ supports from print bed enabled. ...May need to smooth out where the rim is held in after print to get smooth operation.
thingiverse
Powder funnel options for manual powder charged on the Dillon XL650. Options for fitting in station 2 or 3 with clearance for a sizing die, bullet feeder, and primer tube. Use with the standard Dillon powder die and insert. Set the height so that...
thingiverse
Basic allen key holder for dillon 650 / 750 XL reloading presses. ... Use to be clipsed on the casefeeder rod
thingiverse
My solution for repairing side plastic mounts on a Honda Transalp 650 (I call them "piptik"). This will work if only the edge of the mount is broken, but the leg is preserved. The idea is that the repair fastener is screwed into a thread that will...
thingiverse
spent primer tube for dillon xl650 minimized size design
prusaprinters
<p>Where to put that primer rod when the primer feeder is empty?</p><p>Print one or two of the clips and now you have a place to put that rod - just clip them on the safety primer tube and store the rod when not in use (see photos).</p><p>Shown model...
thingiverse
Where to put that primer rod when the primer feeder is empty? Print one or two of the clips and now you have a place to put that rod - just clip them on the safety primer tube and store the rod when not in use (see photos). *>> If you like the...
thingiverse
Not really a remix as its a complete redesign, but the inspiration was gathered from the other part. Made to do the same thing by stopping the case feed lever. ...Holes on the sides allow for storage on the large bolt nearby.
grabcad
Primer Advance Index Stop Switch for Dillon Precision XL-650 and SL-900 Progressive Reloading Press. The switch moves to turn on and off the index by bypassing the indexing lever on the primer feed assembly. Use 0.3125 inch ball and 0.3125 x 0.5...