xm 3d models
569 3d models found related to xm .thingiverse
FrSky XM and XM+ mount for Hantu 5" Frame. I printed it out of TPU so the receiver is snug. It fits nicely on top of my UXII Antenna mount. ...(https://www.thingiverse.com/thing:3150865) or kah00na's AXII Antenna Mount...
thingiverse
Cases for the FrSky XM and XM Plus receivers to provide a little more protection than the clear shrink-wrap that is installed from the factory. This is a simple two piece case which allows access to the BIND button and connections. I'm using the XM...
prusaprinters
Cases for the FrSky XM and XM Plus receivers to provide a little more protection than the clear shrink-wrap that is installed from the factory. This is a simple two piece case which allows access to the BIND button and connections. I'm using the XM...
thingiverse
Customizable model ! ... FrSky XM+ (XM Plus) holder. Mount holes 20x20. ...Need some postprinting cleanup, but hold receiver very strong.
thingiverse
3D desing of the #Darsana XM Anomaly Medal, of the game Ingress
thingiverse
This allows a FrSky XM+ to be mounted in a 20x20 mm stack. ...Print with TPU.
cults3d
A clip together case design for the BeagleBoard-xM developement board.
pinshape
Summary3D desing of the #Darsana XM Anomaly Medal, of the game Ingress
thingiverse
Hi there, Here's a bottom plate for Tyro89 I made, it holds an Frsky XM+ receiver Juste grind a little bit the XM+ support with sandpaper (just a little) to adjust the pressure on the receiver Made in PLA
thingiverse
... allows you to mount the receiver as part of a stack, so that it is super neat. ...Has holes for a zip tie to secure it if you'd like. XM+ purchased here: https://www.banggood.com/Frsky-XM-Micro-D16-SBUS-Full-Range-Receiver-Up-to-16CH-p-1110020.html
thingiverse
... everything else from 3mm acrylic. Full assembly instructions and more pics here: built-to-spec.com/blog/kit-instructions/beagleboard-xm For a kit of this thing go here:http://builttospecstore.storenvy.com/products/833295-beagleboard-xm-enclosure-kit
thingiverse
Simple Half Stack for the XM+. Use double sided tape and heat shrink for a lasting hold. ... **Updated with a new version that is smaller and thinner.
thingiverse
Simple case for the XM+ with right-angle pins. It fits well, but I used a drop of CA on one of the edges. ...You can still get to the bind button and antenna leads.
thingiverse
The XM-35 Baz is a versatile micro missile launcher. This model comes with a removable missile pod, scaled for Master Grade kits. High Grade kit scale might lead to a breakage of some smaller parts on this model. ...Enjoy decimating other mecha with...
thingiverse
I made this case for the Frsky XM+ reciever, I have used some clear tape.to hold the lit on This case is tested and will fit 100% for sure. If you print just one case, go slow and get a good cooling down, the case is tiny. ... Happy printing !
thingiverse
Matt Johnson did the hard work, I added the XM+ slot. Here is the original: https://www.thingiverse.com/thing:2370830 Print on a 45 degree angle with supports. I made it so you can still bind the receiver with it already mounted. I am...
thingiverse
box design to house beagleboard-xm. This box was made to have protection for our beagleboards used on a soundbike. More info on http://timelab.org/en/node/390 Instructions lasercut the parts from 3mm...