xpt2046 touch controller 3d models

The solid representation of the Cisco Touch 10 was successfully constructed using the CAD design software, SolidWorks 2017.

The BL-Touch mounts that are posted don't work because the CR-Touch is fatter and the cable comes out the top. This works fine with the CR-Touch, and should also work with the BL. ... V2 has the probe more centered -- easier to put together.

I've made a mount base for my Creality CR-touch to Petsfang Bullseye Duct from https://www.thingiverse.com/thing:2759439 Changed position of CR-touch, because its enclosure is little different than BL-Touch. ...Also, I added space for connector to...

I added a touch sensor feature, the pad has a path inside to run a wire connected to the TTP223 and makes it touch sensitive, the TTP223 with the antenna works so great that you don't even have to touch the pad, it triggers at around 4cm above the...

I extended the Klemco left fan by ~3mm so I could use the CR touch instead of a BL touch. I am using the CR touch mount from by JKCTX1. I like having dual fans! ...This has a E3D V6 with a Volcano end.

The Adafruit Touch Sensor Breakout is an AT42QT1012-powered device, designed to provide a simple and efficient way to integrate touch sensing capabilities into various projects. ...It features high sensitivity and low power consumption, making it ideal...

Just sitting on a hard surface can cause spurious touch events which enable/disable unwanted features such as Speak to Chat, or play/pause. ... This guard limits touch events to only the areas you're likely to use for play/pause, track advance and...

This is simply a spacer to move your CR Touch (or BL Touch or other Auto Bed Leveling probe with the same screw footprint) 2mm further down. I made it because my CR Touch's activation point was very close to being above the nozzle on my Creality...

This is simply a spacer to move your CR Touch (or BL Touch or other Auto Bed Leveling probe with the same screw footprint) 2mm further down. I made it because my CR Touch's activation point was very close to being above the nozzle on my Creality...

It's the transparent piece inside the old Bose Control Pods.

The insulator slides over the handle and prevents the touch function from working when the red handle is touched. I find it annoying to adjust the temperature or flow as the faucet often turns off and then a second touch is required to turn it on...

The insulator slides over the handle and prevents the touch function from working when the red handle is touched. I find it annoying to adjust the temperature or flow as the faucet often turns off and then a second touch is required to turn it on...

Wombot BL Touch Calibration Tool adjusts your BL Touch to sit precisely 1mm above your nozzle. Lower the nozzle gently until it touches the rounded section, being careful not to push too hard and causing any movement. Then, position the BL Touch onto...

I'm not convinced that the Cocoon Touch requires a MOSFET due to the lack of compatible brackets, but considering its similarities to the Wanhao I3 Plus, I'll take a chance and say that adding a MOSFET won't make it any more hazardous. This design...

This design serves as a mounting bracket for a 3D-Touch or BL-Touch sensor on an Anet A6 3D printer, enabling auto bed leveling functionality. The bracket allows for the sensor to be mounted directly beside the extruder nozzle at its right side,...

... including a socket for plugging in the probe. ... I mounted it to my MPCNC table using drywall screws. Pre-drill for the drywall screws and drill a 15 mm (⅝ ") through hole for the socket connector. Z touch probe: 3.5 mm socket: 3.5 mm jack:

```text >Z_PROBE_OFFSET_FROM_EXTRUDER 0 # Z offset: -below +above [the nozzle] >X_PROBE_OFFSET_FROM_EXTRUDER 46.25 # X offset: -left +right [of the nozzle] >Y_PROBE_OFFSET_FROM_EXTRUDER 0 # Y offset: -front +behind [the nozzle] ``` *** ## CAD file...

This machine comes with Creality V4.3.1 Board which is similar to other Version 4.x board come with a stm32 (ARM) MCU, but with no farther detailed information if any pinout changes, also the machine comes with a nice touch screen which could be a...

This machine comes with Creality V4.3.1 Board which is similar to other Version 4.x board come with a stm32 (ARM) MCU, but with no farther detailed information if any pinout changes, also the machine comes with a nice touch screen which could be a...

A speaker dock for the [SmartiPi Touch 2 case](https://smarticase.com/products/smartipi-touch-2) and a [7.2 inch USB speaker](https://www.amazon.com/gp/product/B086JXJ1LF/) that prints with no supports. Includes an anti-tip bracket. Case is attached...

I designed this one with some messure: - screw hole can be 4mm, use m4 with nuts - the distance of mount hole on KP5 is 19.6mm - the distance of mount hole on 3d touch is 17.6mm Offsets I messured after mount ``` x_offset: -30 y_offset: 8 z_offset:...

This is the precise touch screen I selected: https://www.amazon.com/gp/product/B07N38B86S/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1. ...To relocate the touch screen, I utilized this ribbon cable:...

https://www.thingiverse.com/thing:2759439This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original.The original design did not get my CR Touch close enough to detect the bed, this design should fix that for...

https://www.thingiverse.com/thing:2759439 This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original. The original design did not get my CR Touch close enough to detect the bed, this design should fix that...

This setup is ideal for the 60x60mm touch plate purchased on Amazon and also compatible with the official Carbide 3D touch plate. ...A simple yet effective solution was achieved by using double-sided adhesive tape to mount it securely on the left side...

This mount took inspiration from the mount included with the CR-Touch that fits with the Ender3.This model uses the same dimensions as the parent remix, however it was made fresh in Tinkercad...

A friend wanted a stand for his macropad Eleksmaker Touch Fish, this one https://www.aliexpress.com/item/1005003826469182.html So i made one

I liked the shroud I found by chubbyzook (thing: 4821813). ...So, when it was time for a CR Touch, I remixed this design.

introducing my latest creation: No Touch Door Opener EDC.Design software: SOLIDWORKSSlicer: Prusa slicerFollow up on the updates & the upcoming photos of the print!

I required a BL Touch / 3D Touch bracket for the outside of the hot end housing as I was using a fan duct by: @MakeAny https://www.thingiverse.com/thing:3054313 This mount requires 2 X M3 Nuts + 2 X M3x8 Bolts to mount the BL Touch / 3D Touch to the...