xrt wing mount 3d models
383779 3d models found related to xrt wing mount.thingiverse
New version of the wing mount, this is meant to be flexible but not crush the rear of the body.
thingiverse
Mount on left side front before bulkhead of XRT. One screw attached to receiver box. Print from TPU. ...
cults3d
Mounting plate to install Max6 ESC in an XRT. Has a passage to run the wires for the motor fans or you can still use the stock fan wire mounting location. Includes file for optional power switch mounting bracket. ... Hardware: - (4) M3x 12mm to mount...
thingiverse
M3 x 10mm for the mount to the ESC M3 x 12mm for the mount to the chassis Use the screw removed from the stock ESC for the antenna mount
thingiverse
this is a esc mount for the new traxxas xrt rc car that i made on fusion 360.
cults3d
This plate allows you to mount a Hobbywing Max6 ESC in the same place as the stock XRT ESC. Requires 2 M3x8 and 2 M3x6 pan head screws and 1/8" acrylic or, if you want the plate to last longer than the chassis, Delrin. Make sure to round the edges...
thingiverse
v3 v1: 2x M3x25mm incl. ...spring washer & nuts + 2x M3x12mm incl. washer & nuts. v4 v1: approx. 4-5mm more clearance to the XRT roof skids (5mm longer srews)!
thingiverse
This is a wall mount for the Wing Wing Z84 flying wing (http://www.banggood.com/de/Wing-Wing-Z-84-Z84-EPO-845mm-Wingspan-Flying-Wing-PNP-p-973125.html). Designed to hook into the two small holes underneath the Z84 fuselage. ... I printed it with PLA,...
pinshape
Summary This is a wall mount for the Wing Wing Z84 flying wing (http://www.banggood.com/de/Wing-Wing-Z-84-Z84-EPO-845mm-Wingspan-Flying-Wing-PNP-p-973125.html). Designed to hook into the two small holes underneath the Z84 fuselage. ...I printed it with...
prusaprinters
This is a wall mount for the Wing Wing Z84 flying wing (http://www.banggood.com/de/Wing-Wing-Z-84-Z84-EPO-845mm-Wingspan-Flying-Wing-PNP-p-973125.html). Designed to hook into the two small holes underneath the Z84 fuselage. I printed it with PLA,...
grabcad
This is the transmission cover for the Kyosho PRO-XRT 2WD buggy. ...This part number is SST13 or SST-13.
thingiverse
This is a tool for removing the end caps of XRT Tactical solvent traps. ...It has text on the rear showing the direction to turn for loosening and tightening since it has left hand threads.
thingiverse
Measuring cup for XRT tactical 1" solvent traps. Now you can measure your recovered solvent! Nah, it's obviously a pin wrench. Fits both adapter and end cap. The pins are 1/8" x 3/8" stainless. Drive them in until they fully bottom out. ...
cults3d
Reinforces the XRT's front bumpers a little. The 2nd file is wider at the hooks so it doesn't come out easily, but it's harder to get in. ... The holes on the sides are for those who want to attach them to the bumper.
thingiverse
Use as battery tray for XRT Traxxas. Infill 25% or less. I prefer TPU but PLA or similar will too to. PLA may crack on impact on jumps. Space under the tray for the straps. Nut holes are 4,5mm deep so you can use self-locking nuts. ...