xt 90 connector 3d models
113517 3d models found related to xt 90 connector.thingiverse
I need to use the 4-6s large lipos for my F550, they come with 12awg wires which are pretty thick, so you really need a beefy connector or its a tight squeeze into the xt60 connectors, so I stick with the XT90's for the 4-6's large 5-6amp lipos. ...Here...
cults3d
I need to use the 4-6s large lipos for my F550, they come with 12awg wires which are pretty thick, so you really need a beefy connector or its a tight squeeze into the xt60 connectors, so I stick with the XT90's for the 4-6's large 5-6amp lipos. ...Here...
cgtrader
I need to use the 4-6s large lipos for my F550, they come with 12awg wires which are pretty thick, so you really need a beefy connector or its a tight squeeze into the xt60 connectors, so I stick with the XT90's for the 4-6's large 5-6amp lipos. Here...
thingiverse
... mount is made for the xt-90H with the end cap this is a xt-90 mount for the losi baja rey / rock rey 10th scale. the xt-90 connector fits very tight in the mount to secure it in place, it uses the stock plug holder thingy uses stock screws m2.6
cults3d
This is a holder to replace the original traxxas one if you want to convert to XT-90 that are more reliable. I made 2 hole / plug so you can put 2 set screws in there to hold them real good. ... I also put a thin layer over the holes so you don't need...
thingiverse
XT-60 Connector Cover. ...You can see which battery "Full" or "Empty"
thingiverse
This new XT-30 connector cap design features a finger grab section on top for ease of installation and removal, and the never seen before retention loop on the side of the cap. Use this loop to store your battery's cap on an open switch of your...
thingiverse
This new xt-60 connector cap design features a finger grab section on top for ease of installation and removal, and the never seen before retention loop on the side of the cap. Use this loop to store your battery's cap on an open switch of your...
thingiverse
XT-90 Mount designed to hold 2 Male connectors with a right angle flush wire exit hole between them. ... This allows power facing one way and a loop key facing the other way with room for 10 AWG wiring and bridge inside the mount 2mm pilot holes for...
thingiverse
Dean-T / XT power connector model with real dimensions This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/fA6RxQxDniv
thingiverse
***NOT FOR COMMERCIAL USE*** Update: Added XT-90 and 10awg options - Fits 16mm and 20mm straps - Amass XT-60 connectors - 12awg and 14awg versions.
thingiverse
... I've replaced the original 2 files for a single file that should fit both authentic and fake XT-60 Connectors. If this is too tight you may want to adjust your extrusion. ... This works for me on all my XT60 Connectors (both real and fake).
thingiverse
A remix of AdrionAce's XT-60 socket holder. Re-modelled with a more compact footprint and screw-friendly mounting holes. Designed for a 5mm screw. ...I use this as a quick-coupling for my heated bed.
thingiverse
This loop-key bracket holds an XT-90 female plug, and a small button switch. Wire a small-value resistor, e.g. 220Ω, to charge your ESC without massive inrush current. Use a bit of heavy gauge wire on a matching connector to make your key. Hold the...
thingiverse
I made this connector so i could connect my brushless motor to the ESC of my rc plane. ...It is designed without any extra clearance for inserting the pins so it is a tight fit.
thingiverse
A cap for the XT-90s anti-spark connector. ...Note: it's a very tight fit.
thingiverse
These are protector caps for XT-60 connectors. Caps should be printed out of TPU. The main purpose of the caps is to identify which batteries are charged and those that are not. This design is reversible which makes it easy to take off and put...
thingiverse
Hi, this is angle connector 20x20 mm 90° with bean hole 4x14 mm.
thingiverse
... various filter materials. ...The connectors worked well to keep the corners at a perfect 90 degrees. ...I used this same connector to make the side connectors (I just moved it in the -Z direction so the bottom would not be printed (see Cura picture).
thingiverse
This is a Remix of an DB9 connector from: https://www.printables.com/de/@Ouwekaas https://www.printables.com/de/model/409740-db9-housing-at-a-90-degree-angle The cable goes in a 90 degree angle out of the side of the housing. ... Parts needet: 2X...
thingiverse
90° connector for the 5mm thick Elmers posterboard. ...Being used to create a box around my printer for sound dampening and better light control to view my prints from another room via camera.
grabcad
This is a simplified model of a 90 degree connector, I use it for layouts. ...Noticed the site did not have a file on it, so I decided to add mine.