xt60 with capacitor 3d models
2767334 3d models found related to xt60 with capacitor.thingiverse
XT60 mount designed for the Hyperlite Floss 2 / 2.1 frame. ...Also incorporates two Panasonic 1000uf 35v capacitors which can be found at Pirofliprc.com http://pirofliprc.com/PANASONIC-1000UF-35V-LOW-ESR-CAPACITOR_p_4537.html
thingiverse
XT60 holder with 2cm diameter capacitor place for the strip. ... print with high fill.
thingiverse
This is an XT60 holder for the drone side. ... Holds a 12.75 diameter 50v/1000uf capacitor for 6S drones. Print with TPU, cooling and retraction off. ...I always use a brim with TPU for extra adhesion.
thingiverse
Also included is a mount for your XT60 connector and a 1000mfd 50v Panasonic FM series capacitor on the rear. You will need (2) M3x25mm bolts with flanged lock-nuts for the GoPro mount. I highly recommend using washers to mount the Command Center...
thingiverse
AMASS XT60 Capacitor Holder Holds 35v 470uF Capacitor (or any other cap with 10.4mm diameter) Use TPU or you might need to scale up a bit for other materials
thingiverse
A simple holder to hold a Panasonic 1000uf capacitor on an xt60 connector.
thingiverse
"Dry-fit" before soldering and solder everything together with the XT60 and capacitor halfway installed. Then slide the assembly into the final position. ...The part is long enough to allow you to fill the back of the XT60 with hotglue to provide...
thingiverse
if the tube is to tight for the Capacitor heat it up with a lighter for a few seconds and push it in here you can find colored XT60´s, Capacitors & flexible Filament: - Bangood - XT60 orange - Bangood - XT60 red - Bangood - XT60 black - Bangood -...
thingiverse
A mount to hold a 470µF capacitor on an XT60 connector. ... It may not fit all capacitors, the diameter is 10.5mm.
thingiverse
XT60 - 220uf Capacitor Mount Slides over an XT60 and provides a hole for a 35v 220uf Capacitor to go next to it. Aimed at stopping the capacitor from moving around too much. Please note this may be quite a tight fight and may require some filing or...
thingiverse
Didn´t find a neat XT60/capacitor holder that suited my demands so i designed my own. It holds a 25V 1000uF capacitor that measure 10mm in diameter and around 17mm long. The legs folds down in channels for insulation. ...Just add some hest shrink to...
thingiverse
Used capacitor:https: //www.banggood.com/20pcs-1000uF-25V-Radial-Electrolytic-Capacitor-10-x-17mm-105C-p-1022623.html?rmmds=myorder
thingiverse
Holds the capacitor on the pigtail nice and clean like. I used a solder iron to weld the lid on. ... Printed in tpu.
thingiverse
This is an XT60 with 1000UFl capacitor holder for the Armattan Badger or Marmott.
cults3d
I needed a protection for my capacitor which tightened together with my XT60 socket so I made two models The first is for 470 UF capacitors a version open on the upper part and another one can be closed I didn't need this second part but I had a...
thingiverse
Nazgul rear print with XT60 / Capacitor and VTX antenna slot. ... Adapted for original spacer (d=6mm) Compatible with additional print for immortal-T antenna (not included) I printed it with TPU : - support - 20mm/s - retractation 4mm - 45mm/s - No fan...
thingiverse
RH XT60 with 11mm Capacitor mount added, can probably be flipped for the left hand side. ...also shortened from the original.
thingiverse
I like a lot of the existing designs for capacitor holders, but didn't find one for a the 50V 1000uF capacitor I had, so I sketched one up really quickly. ... This was made from scratch in Fusion360 and I wouldn't consider it a remix, but I was...
thingiverse
This is a complete back pack XT60, GPS, SMA Antenna, 12mm diameter capacitor for the AOS 5" V2 frame. I added a condensed version, lighter, without capacitor, on which you can mount either 2 vetical short 2.4ghz antennas (one vertical, one...
thingiverse
I took the opportunity to remake a tail, a capacitor assembly and an XT60 that goes between the propeller protections. You don't have to put a GPS, but you can use the tail to mount an autonomous buzzer, it's designed for both. Since I do anything...
grabcad
3D model of the capacitor with legs bend at 45deg. It includes a upside and also downside bend. ...This model was created using FreeCAD that original model file is also included.
youmagine
This is a 3D printed Flux Capacitor with the option of putting electronics inside to make it light up with LEDs. This is meant to be a fun printing/electronics project and not meant to be a hyper-realistic prop. So have fun with it! :) Watch...
myminifactory
This is a 3D printed Flux Capacitor with the option of putting electronics inside to make it light up with LEDs. This is meant to be a fun printing/electronics project and not meant to be a hyper-realistic prop. So have fun with it! :) Watch these...
cults3d
This is a 3D printed Flux Capacitor with the option of putting electronics inside to make it light up with LEDs. This is meant to be a fun printing/electronics project and not meant to be a hyper-realistic prop. So have fun with it! :) Watch these...
pinshape
Requested by fma :). This is a 3D printed Flux Capacitor with the option of putting electronics inside to make it light up with LEDs. This is meant to be a fun printing/electronics project and not meant to be a hyper-realistic prop. So have fun with...
thingiverse
This is a 3D printed Flux Capacitor with the option of putting electronics inside to make it light up with LEDs. This is meant to be a fun printing/electronics project and not meant to be a hyper-realistic prop. So have fun with it! :) Watch...
thingiverse
Hi all, great little file, I just remixed it a bit to hold my larger 50v 1000uF caps. Done in TPU. ... Thanks to the original designer!