xtend plus driver 3d models

I frequently use these bits, both with my trusty hand driver and the convenient rechargeable screwdriver. ... Magnetic Screwdriver Set: https://www.amazon.com/gp/product/B06XY4C51D Keyless Chuck: https://www.amazon.com/gp/product/B06XWY4NP6 Allen Bits:...

This is a driver for a 8" lathe's compound slide. It slides onto a 1/4" hex shanked 3/8" socket adapter. Then a drill or power screwdriver can turn the slide. It will work with ether on or two of the handles installed. I've been using it with...

refinement of kheibert's stubby screw driver handle. I took it into meshmixer and smoothed out all the sharp edges. ...I also added a slight taper inside the hole, so that the bit will be held in more tightly (although if you push too far, you may need...

I blended the screwdriver with the wire nut driver, then attached a clip. Kudos to H5Labs & tomlombardi for their contributions! Update: I created a separate file without the clip, which has proven to be a better fit and works seamlessly in my tool...

Driver Tool for a Standard Nut fits most Nuts with an interior diameter of at least 6.56mm x 6.56mm and a smaller outer dimension of 12mm perfectly. This was made to match the one that comes packaged with the Ultimaker Olsson Block. ... Print Settings ...

For Chinese LED Driver (Size 24x56 mm) 10x3W LEDs, Make an Alignment Adjustment to the Z-Axis Mirror!\nPrint Settings\nPrinter Brand:\n Prusa\n \n Printer Model:\n Prusa Steel\n \n Raft Option: Off\n No Rafts\n \n Support Option: Off\n No Supports\n...

I combined the screwdriver with the nut driver, attaching a clip to make one convenient tool. Huge thanks go out to H5Labs and tomlombardi for creating this innovative solution! Update: I removed the clip and added a new file version without it. This...

This is a coolant tank bracket used to relocate the coolant tank from the passenger side of the engine bay to the driver side. It works for n54 cars and LS swapped cars. 60% might be a little too much infill but I wanted it to be plenty strong and...

I designed two versions of a 1/4 socket hand driver - one with a ratchet and the other without. The single-piece model works efficiently, but I created the two-part version to allow printing the shaft horizontally, thereby increasing its strength.

... a circle just a little oversized for the pot's adjustment screw. The design also has two shoulders on the shank so you can align the flathead blade. This was designed to fit the iFixit Precision Screwdriver set, but should fit an 4mm driver. ...

The main advantages of this design over the ones in thingverse is that the screw drivers can "stand up" on the table as their bottoms are flat and that they have a holder which displays them. ...Also the openscad files are available for you to...

Upgrade Your Cycling Experience with a New Deore Driver 520 Button Are you tired of dealing with worn-out or damaged buttons on your trusty Deore Driver 520? Do you struggle to get the most out of your gear shifting due to faulty controls? Look no...

Similarly, the bits simply slide into the holes provided (up to 7 bits) and are elastically gripped. This holder must be printed in some kind of FLEX filament. Note: After using this for a while, I found that it sometimes slipped off when the driver...

The design accommodates a driver with an outside diameter of 11.5 centimeters and a cutout of 9.5 centimeters. You can install a female RCA plug in the rear for easy wiring. This design is an open type, which I won't attempt to justify through audio...

Design Storage and organization rack for precision drivers designed to mount to a workbench which accommodates [hanging bins](https://www.uline.com/BL_305/Uline-Plastic-Stackable-Bins). Specifically made for [Wiha...

Recently I discovered a compact mosfet module called "Little Driver" by Digital Sqrt, designed to switch high current bed heater remotes from motherboards with an advantage of direct connection to main power supplies without loading main boards, thus...

About this Model: Features: Modified to be 1x6 without overhang. Uses 3x3 Neodymium magnets to affix a top, however I have not created this yet. Designed to be modular and allow an additional 38x105mm insert to be added within the case. Driver...

Fan shroud for the Trex-3 enhances driver cooling significantly, so it's recommended to print with supports attached only to the bed. This setup will suffice, but you might need to use supports in your profile settings anyway. A nut has been inserted...

Another crucial piece of my Bi-LED Retrofit installation was these custom LED Driver enclosures I crafted to perfectly replace the OEM Matsushita ballasts. These could benefit from some minor tweaks, particularly in the snap-fit design and the area...

This handle serves as a manual driver's side seat height adjustment for a 2013 Passat. It may also fit other years and models of this vehicle. A picture of the metal shaft is included in the submission, allowing users to see its design. The design...

A driver to hold a LM2596S buck converter often used to allow the use of 12v Noctua fans on 24V systems like the Voxelab Aquila. This fits the Aquila as it has an empty space under it where the Ender 3 V2 has it's tool draw. This is to fit the...

I have designed this helmet head driver to be used with the most popular 1/10 Rally or Touring Rc cars cockpits since the one offered with these kits are (really) outdated and if you have a contemporary WRC body shell, with two of these it will look...

Featuring a top-notch Polygonal Model, this Driver's Airbag is animated using Point Cache and boasts high realism in fold representation. The project was created in 3ds Max versions 2017, 2016, and 2014 with V-Ray 3.4 for superior visual effects. The...

A small enclosure is required for the Blackbuck 8M laser driver, featuring an Anode/Cathode End that will be connected to the laser diode via a 2-pin Molex Mini FIT JR female socket. The lid has been engineered with a cutout allowing for current...

I designed this to support EZOUT and the aluminum MK8 extruder driver specifically for flexible filament. To slide the unit between the z axis screw rod and vertical frame rail, you must remove the top horizontal frame support rail. The run out...

Howdy, I wanted to try my first hand at modeling in Fusion 360 and needed a holder for the millions of drivers I have accumulated. Most of what I saw on Thingiverse is for the newer 1/4" pegboard but I have an older 3/16" pegboard. The hooks diameter...

It's my design for a case to replace the cheap plastic tray these hex drivers came in years ago. The geometry at the top of the handle is slightly different than what is already available. This was a great project to cut my teeth and aim for some...

Variety of Racks for Wiha Screw Drivers 9/18/2016: A new Wiha_7pc_26390.stl upload was incorrectly exported, so a good export has taken its place. 4/3/2017: This Wiha set doesn't quite fit right, let me know if it's yours and I might be able to...

Unfortunately, I ended up burning out the driver and fan wiring due to an incorrect connection. Thankfully, replacing the board was significantly cheaper than purchasing a new laser. The replacement board I found was larger in size, so I designed and...

I had a random hex driver and its 32 hex bits laying around so I decided to make a holder for them to make it a bit more tidy.The tolerances are bit wrong so the fit is really really snug for the bits, I have to use pliers to get them out but since I...